PS21267-P Mitsumi Electronics, Corp., PS21267-P Datasheet
![no-image](/images/manufacturer_photos/0/4/452/mitsumi_electronics__corp__sml.jpg)
PS21267-P
Available stocks
Related parts for PS21267-P
PS21267-P Summary of contents
Page 1
... Fault signaling : Corresponding fault (Lower-side IGBT fault (Lower-side supply). • Input interface : 3, 5V line compatible. (High Active) • UL Approved : Yellow Card No. E80276 APPLICATION AC100V~200V three-phase inverter drive for small power motor control. (Short-pin type : PS21267-P) Fig. 1 PACKAGE OUTLINES 27×2.8(=75.6) 2.8 ±0.3 ...
Page 2
... OFF and a fault signal (Fo) is output. Since the SC fault may be repetitive recommended to stop the system when the Fo signal is received and check the fault Collector current waveform 0 2 PS21267-P/AP TRANSFER-MOLD TYPE INSULATED TYPE C2 (Note 7) C1 (Note 6) Protection circuit (UV) DIP-IPM H-side IGBT S ...
Page 3
... V = 13.5~16.5V, Inverter part 125°C, non-repetitive, less than 2 µs j 60Hz, Sinusoidal minute, connecting pins to heat-sink plate Control terminals Heat sink boundary T C PS21267-P/AP TRANSFER-MOLD TYPE INSULATED TYPE Ratings 450 500 600 30 60 55.5 (Note 1) –20~+125 ≤ 100°C) however, to in- C ≤ ...
Page 4
... Trip level Reset level C = 22nF FO Applied between according to the following approximate equation : C FO PS21267-P/AP TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — — 1.80 — — 3.00 — — 0.067 Limits Min. Typ. Max. ...
Page 5
... Between rated current and DB 1.7 times of rated current –20°C ≤ T ≤ 100°C, C N-line wiring inductance less Between 1.7 times and than 10nH (Note 9) 2.0 times of rated current between V -N (including surge) NC PS21267-P/AP TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — 0.98 1.47 — — 54 — ...
Page 6
... Di2 COM S HVIC3 V V IGBT3 Di3 COM S IGBT4 LVIC Di4 U OUT V CC IGBT5 Di5 V OUT U N IGBT6 Di6 OUT CIN GND CFO CFO CIN PS21267-P/AP TRANSFER-MOLD TYPE INSULATED TYPE DIP-IPM Oct. 2005 ...
Page 7
... Fig. 6 PACKAGE OUTLINES (Long-pin type : PS21267-AP) ±0.5 ±0.5 0.5MAX remains solder Irregular (1) ±0.5 28 ±0.5 (11.5) (8.5) 0.5MAX remains solder 21.4 13.4 ±0.5 (1) 35 ±0.6 31 ±0.5 11.5 ±0.5 PS21267-P/AP TRANSFER-MOLD TYPE INSULATED TYPE 0.6 0.6 Irregular 16 ±0.5 8 ±0.5 5° Oct. 2005 ...
Page 8
... DELAY level, the circuits start to operate when the next input is applied set by the external capacitor C O RESET SET PS21267-P/AP TRANSFER-MOLD TYPE INSULATED TYPE . FO , and F outputs continuously during UV period RESET b6 b7 Oct. 2005 ...
Page 9
... (Logic) NC Wiring inductance should be less than 10nH. width=3mm, thickness=100µm, length=17mm in copper pattern (rough standard) N Shunt resistor Please make the connection point as close as possible to the terminal of shunt resistor. PS21267-P/AP TRANSFER-MOLD TYPE INSULATED TYPE RESET Oct. 2005 ...
Page 10
... C4 The long wiring of GND might generate If this wiring is too long, the SC level noise on input and cause IGBT to fluctuation might be larger and cause be malfunction. SC malfunction. PS21267-P/AP TRANSFER-MOLD TYPE INSULATED TYPE DIP-IPM this wiring is too long, short circuit might be caused ...