LT6552IS8 Linear Technology, LT6552IS8 Datasheet
LT6552IS8
Specifications of LT6552IS8
Available stocks
Related parts for LT6552IS8
LT6552IS8 Summary of contents
Page 1
... The LT6552 is available in the 8-lead SO package as well as a tiny, dual fine pitch leadless package (DFN). The device is specified over the commercial and industrial temperature ranges. , LTC and LT are registered trademarks of Linear Technology Corporation OUT 75 ...
Page 2
... Figure 1 shows the DC test circuit unless otherwise noted 1k. (Note CONDITIONS Both Inputs (Note 7) Any Input Either Input Pair ORDER PART TOP VIEW NUMBER 8 FB LT6552CS8 + 7 V LT6552IS8 6 OUT SHDN 5 S8 PART MARKING S8 PACKAGE = 100 C/W 6552 JA 6552I MIN TYP MAX UNITS ...
Page 3
ELECTRICAL CHARACTERISTICS operating temperature range, otherwise specifications are 1V 0V REF CM DIFF SHDN SYMBOL PARAMETER e Input Noise Voltage Density n i Input Noise Current Density ...
Page 4
LT6552 5V ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are 1V 0V REF CM DIFF SHDN SYMBOL PARAMETER V Input Offset Voltage Input V Drift ...
Page 5
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are 0V unless otherwise noted. R DIFF SHDN SYMBOL PARAMETER t Turn-On Time ON t Turn-Off Time OFF Shutdown Output Leakage Current 5V ELECTRICAL ...
Page 6
LT6552 5V ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are 0V unless otherwise noted. R DIFF SHDN SYMBOL PARAMETER Shutdown Pin Current t Turn-On Time ON t Turn-Off Time OFF Shutdown Output ...
Page 7
W U TYPICAL PERFOR A CE CHARACTERISTICS Supply Current vs Supply Voltage 125 – ...
Page 8
LT6552 W U TYPICAL PERFOR A CE CHARACTERISTICS Open-Loop Gain 500 400 300 200 100 –100 R = 150 L –200 –300 –400 –500 –5 –4 –3 –2 – ...
Page 9
W U TYPICAL PERFOR A CE CHARACTERISTICS Output Impedance vs Frequency 100 0.1 0.01 100k 1M 10M 100M FREQUENCY (Hz) 6552 G19 Common Mode Rejection Ratio ...
Page 10
LT6552 W U TYPICAL PERFOR A CE CHARACTERISTICS Large Signal Response 5V 6552 G27 50ns/DIV 5pF 10pF 500 ...
Page 11
U U APPLICATIO S I FOR ATIO The LT6552 is a video difference amplifier with two pairs of high impedance inputs. The primary purpose of the LT6552 is to convert high frequency differential signals into a single-ended output, while rejecting ...
Page 12
LT6552 U U APPLICATIO S I FOR ATIO Amplifier Characteristics Figure 5 shows a simplified schematic of the LT6552. There are two input stages; the first one consists of transistors for the (+) and (–) inputs while ...
Page 13
U U APPLICATIO S I FOR ATIO Layout and Passive Components With a bandwidth of 75MHz and a slew rate of 600V/ s, the LT6552 requires special attention to board layout and supply bypassing. Use a ground plane, short lead ...
Page 14
LT6552 U U APPLICATIO S I FOR ATIO SHDN Pin The LT6552 includes a shutdown feature that disables the part, reducing quiescent current and making the output high impedance. The part can be shutdown by bringing the – SHDN pin ...
Page 15
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... Slew Rate, Rail-to-Rail Output, Input Common Modes to Ground Internal Gain of 2, 110MHz –3dB Bandwidth, Input Common Modes to Ground www.linear.com 499 5.6pF 909 2.2pF 1.3k 1pF 0.5dB) > 25MHz BW (–3dB) > 36MHz I 70mA 6552 TA02 S LT/TP 0304 1K • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2003 6552f ...