AT32UC3A464S Atmel Corporation, AT32UC3A464S Datasheet - Page 85

• Manufacturer Part Number: AT32UC3A464S
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A464S

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: AES
• Sram (kbytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.3.2
10.3.3
10.3.4
32072G–11/2011
USB
ADC
USART
Fix/Workaround
Make a DTLB Protection (Write) exception handler which permits the interrupt request to be
handled in privileged mode.
As a consequence, isochronous IN and OUT tokens are sent every 1ms (Full Speed), or
every 125uS (High Speed).
Fix/Workaround
For higher polling time, the software must freeze the pipe for the desired period in order to
prevent any "extra" token.
Sleep Mode activation needs additional A to D conversion
If the ADC sleep mode is activated when the ADC is idle the ADC will not enter sleep mode
before after the next AD conversion.
Fix/Workaround
Activate the sleep mode in the mode register and then perform an AD conversion.
ISO7816 info register US_NER cannot be read
The NER register always returns zero.
Fix/Workaround
None.
The LIN ID is not transmitted in mode PDCM='0'
Fix/Workaround
Using USART in mode LIN master with the PDCM bit = '0', the LINID written at the first
address of the transmit buffer is not used. The LINID must be written in the LINIR register,
after the configuration and start of the PDCA transfer. Writing the LINID in the LINIR register
will start the transfer whenever the PDCA transfer is ready.
The LINID interrupt is only available for the header reception and not available for the
header transmission
Fix/Workaround
None.
USART LIN mode is not functional with the PDCA if PDCM bit in LINMR register is set
to 1
If a PDCA transfer is initiated in USART LIN mode with PDCM bit set to 1, the transfer never
starts.
Fix/Workaround
Only use PDCM=0 configuration with the PDCA transfer.
The RTS output does not function correctly in hardware handshaking mode
The RTS signal is not generated properly when the USART receives data in hardware hand-
shaking mode. When the Peripheral DMA receive buffer becomes full, the RTS output
should go high, but it will stay low.
Fix/Workaround
Do not use the hardware handshaking mode of the USART. If it is necessary to drive the
RTS output high when the Peripheral DMA receive buffer becomes full, use the normal
UPCFGn.INTFRQ is irrelevant for isochronous pipe
85