AT32UC3B1128 Atmel Corporation, AT32UC3B1128 Datasheet - Page 126
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT32UC3B1128
Manufacturer Part Number
AT32UC3B1128
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(377 pages)
2.AT32UC3A0128.pdf
(33 pages)
3.AT32UC3A0128.pdf
(159 pages)
4.AT32UC3B0128.pdf
(684 pages)
5.AT32UC3B0128.pdf
(107 pages)
Specifications of AT32UC3B1128
Flash (kbytes)
128 Kbytes
Pin Count
48
Max. Operating Frequency
60 MHz
Cpu
32-bit AVR
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
28
Ext Interrupts
28
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
1
Uart
2
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
6
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.0-3.6 or (1.65-1.95+3.0-3.6)
Operating Voltage (vcc)
3.0-3.6 or (1.65-1.95+3.0-3.6)
Fpu
No
Mpu / Mmu
Yes / No
Timers
10
Output Compare Channels
16
Input Capture Channels
6
Pwm Channels
13
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT32UC3B1128-U
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
9.5.2
9.5.2.1
9.5.2.2
9.5.3
9.5.3.1
32002F–03/2010
Branch message packets
Special cases
Instruction count packet
Compressed program counter packets
Debug Mode
The Nexus standard also specifies Program Trace Correction messages to correct for specula-
tively transmitted trace messages, but these are not implemented in the AVR32, since program
trace messages are only transmitted for actually executed instructions. Similarly, the Nexus-
specified CANCEL packet of synchronized branch messages is not implemented in AVR32.
Entry into Debug Mode will generate an program trace correlation message, while no trace mes-
sages are generated while executing in Debug Mode. A Program Trace Synchronization
message is transmitted when Debug Mode is exited.
The program trace messages contain packets which identify the address of the taken branch,
the target of the branch, and the current program counter value. These packets are discussed
below.
In several of the program trace messages, an Instruction Count (I-CNT) packet is included, to
identify the number of sequentially executed instruction units since the last program trace mes-
sage. In AVR32, this figure refers to bytes, i.e. compact instructions count two bytes and
extended instructions are four bytes.
The following rules apply to instruction counts:
To save bandwidth, the Nexus messages employ compressed versions of the program counter
address. These include:
U-ADDR = StripLeadingZeros (Previous sent addr xor uncompressed address from pipeline).
F-ADDR = Full target address for a taken branch. Leading zeroes may be truncated.
When entering Debug Mode, a PTC message is generated with EVCODE = 0.
When exiting Debug Mode, a PTSY message is generated. If the instruction also generates a
branch message, the branch message with sync (i.e. PTDBS or PTIBS) is generated instead of
3. Program Trace, Indirect Branch messages with sync contain both instruction count and
4. Program Trace, Resource full messages is transmitted when an internal buffer over-
5. Program Trace Correlation. This message is transmitted to synchonize the program
• A taken indirect branch which generates a trace message is not included in the instruction
• An indirect branch which is not taken is included in the instruction count.
• Speculatively fetched instructions are not counted until they are actually executed.
• The instruction counter is reset every time a program trace message is generated.
count.
PC, and are transmitted instead of a Program Trace Synchronization message if a syn-
chronization condition occurs and the current instruction is a taken direct/indirect
branch.
flows. ICNT is transmitted whenever it overflows with this message.
trace with an event. Sent when trace is disabled, debug mode is entered or sleep mode
is entered.
AVR32
126