AT32UC3C2512C Atmel Corporation, AT32UC3C2512C Datasheet - Page 100
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT32UC3C2512C
Manufacturer Part Number
AT32UC3C2512C
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(377 pages)
2.AT32UC3A0128.pdf
(159 pages)
3.AT32UC3C0128C.pdf
(1313 pages)
4.AT32UC3C0128C.pdf
(108 pages)
Specifications of AT32UC3C2512C
Flash (kbytes)
512 Kbytes
Pin Count
64
Max. Operating Frequency
66 MHz
Cpu
32-bit AVR
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
45
Ext Interrupts
64
Usb Transceiver
1
Quadrature Decoder Channels
1
Usb Speed
Full Speed
Usb Interface
Device + OTG
Spi
5
Twi (i2c)
2
Uart
4
Can
2
Lin
4
Ssc
1
Ethernet
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
11
Adc Resolution (bits)
12
Adc Speed (ksps)
2000
Analog Comparators
2
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
68
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.0 to 3.6 or 4.5 to 5.5
Operating Voltage (vcc)
3.0 to 3.6 or 4.5 to 5.5
Fpu
Yes
Mpu / Mmu
Yes / No
Timers
3
Output Compare Channels
13
Input Capture Channels
6
Pwm Channels
14
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3C2512C-A2UR
Manufacturer:
YAGEO
Quantity:
60 000
Company:
Part Number:
AT32UC3C2512C-U
Manufacturer:
ATMEL
Quantity:
125
Company:
Part Number:
AT32UC3C2512C-Z2ZR
Manufacturer:
Atmel
Quantity:
1 499
10.2
10.2.1
10.2.2
10.2.3
10.2.4
32117CS–AVR-08/11
rev D
AST
aWire
GPIO
Power Manager
1
1
1
1
2
3
AST wake signal is released one AST clock cycle after the BUSY bit is cleared
After writing to the Status Clear Register (SCR) the wake signal is released one AST clock
cycle after the BUSY bit in the Status Register (SR.BUSY) is cleared. If entering sleep mode
directly after the BUSY bit is cleared the part will wake up immediately.
Fix/Workaround
Read the Wake Enable Register (WER) and write this value back to the same register. Wait
for BUSY to clear before entering sleep mode.
aWire MEMORY_SPEED_REQUEST command does not return correct CV
The aWire MEMORY_SPEED_REQUEST command does not return a CV corresponding to
the formula in the aWire Debug Interface chapter.
Fix/Workaround
I s s u e a d u m m y r e a d t o a d d r e s s 0 x 1 0 0 0 0 0 0 0 0 b e f o r e i s s u i n g t h e
MEMORY_SPEED_REQUEST command and use this formula instead:
Clearing Interrupt flags can mask other interrupts
When clearing interrupt flags in a GPIO port, interrupts on other pins of that port, happening
in the same clock cycle will not be registered.
Fix/Workaround
Read the PVR register of the port before and after clearing the interrupt to see if any pin
change has happened while clearing the interrupt. If any change occurred in the PVR
between the reads, they must be treated as an interrupt.
Clock Failure Detector (CFD) can be issued while turning off the CFD
While turning off the CFD, the CFD bit in the Status Register (SR) can be set. This will
change the main clock source to RCSYS.
Fix/Workaround
Solution 1: Enable CFD interrupt. If CFD interrupt is issues after turning off the CFD, switch
back to original main clock source.
Solution 2: Only turn off the CFD while running the main clock on RCSYS.
Requesting clocks in idle sleep modes will mask all other PB clocks than the
requested
In idle or frozen sleep mode, all the PB clocks will be frozen if the TWIS or the AST need to
wake the cpu up.
Fix/Workaround
Disable the TWIS or the AST before entering idle or frozen sleep mode.
TWIS may not wake the device from sleep mode
f
sab
=
---------------- -
CV 3
7f
aw
–
AT32UC3C
100