ATmega48A Atmel Corporation, ATmega48A Datasheet - Page 292

• Manufacturer Part Number: ATmega48A
• Manufacturer: Atmel Corporation

Specifications of ATmega48A

• Flash (kbytes): 4 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 256
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27.8.14
In
Table 27-7.
Table 27-8.
For details about these two section, see
Write Section” on page 281
Table 27-9.
Note:
8271D–AVR–05/11
BOOTSZ1
Section
Read-While-Write section (RWW)
No Read-While-Write section (NRWW)
Variable
PCMSB
PAGEMSB
ZPCMSB
ZPAGEMSB
PCPAGE
PCWORD
Table 27-7
1
1
0
0
1. Z15:Z13: always ignored
ATmega88A and ATmega88PA Boot Loader Parameters
Z0: should be zero for all SPM commands, byte select for the LPM instruction.
See
Programming.
BOOTSZ0
through
Boot Size Configuration, ATmega88A/88PA
Read-While-Write Limit, ATmega88A/88PA
Explanation of Different Variables used in
”Addressing the Flash During Self-Programming” on page 285
1
0
1
0
Table
Boot
Size
128 words
256 words
512 words
1024 words
PC[11:5]
PC[4:0]
Note:
11
4
27-9, the parameters used in the description of the self programming are given.
The different BOOTSZ Fuse configurations are shown in
Pages
16
32
4
8
”NRWW – No Read-While-Write Section” on page 281
Corresponding
Z-value
Application
Flash
Section
0x000 - 0xF7F
0x000 - 0xEFF
0x000 - 0xDFF
0x000 - 0xBFF
Z12:Z6
Z5:Z1
Z12
Z5
ATmega48A/PA/88A/PA/168A/PA/328/P
(1)
Figure 27-3
Boot
Loader
Flash
Section
0xF80 - 0xFFF
0xF00 - 0xFFF
0xE00 - 0xFFF
0xC00 - 0xFFF
Description
Most significant bit in the Program Counter. (The Program Counter is
12 bits PC[11:0])
Most significant bit which is used to address the words within one
page (32 words in a page requires 5 bits PC [4:0]).
Bit in Z-register that is mapped to PCMSB. Because Z0 is not used,
the ZPCMSB equals PCMSB + 1.
Bit in Z-register that is mapped to PAGEMSB. Because Z0 is not
used, the ZPAGEMSB equals PAGEMSB + 1.
Program counter page address: Page select, for page erase and
page write
Program counter word address: Word select, for filling temporary
buffer (must be zero during page write operation)
Pages
96
32
and the Mapping to the Z-pointer, ATmega88A/88PA
for details about the use of Z-pointer during Self-
End
Application
Section
0xF7F
0xEFF
0xDFF
0xBFF
Address
0x000 - 0xBFF
0xC00 - 0xFFF
Figure 27-2 on page
0xF80
0xF00
0xE00
0xC00
Boot Reset Address (Start Boot Loader
Section)
and
”RWW – Read-While-
283.
292