ATtiny28L Atmel Corporation, ATtiny28L Datasheet - Page 44
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATtiny28L
Manufacturer Part Number
ATtiny28L
Description
Manufacturer
Atmel Corporation
Specifications of ATtiny28L
Flash (kbytes)
2 Kbytes
Pin Count
28
Max. Operating Frequency
4 MHz
Cpu
8-bit AVR
Hardware Qtouch Acquisition
No
Max I/o Pins
11
Ext Interrupts
10
Usb Speed
No
Usb Interface
No
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.03
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
1
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATtiny28L-1AC
Manufacturer:
ATMEL
Quantity:
1 187
Company:
Part Number:
ATtiny28L-1AI
Manufacturer:
ATMEL
Quantity:
2 840
Part Number:
ATtiny28L-4AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny28L-4MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny28L-4PC
Manufacturer:
EPCOS
Quantity:
3 000
Part Number:
ATtiny28L-4PC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny28L-4PU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Analog Comparator
Register Description
Analog Comparator Control
and Status Register – ACSR
44
ATtiny28L/V
The analog comparator compares the input values on the positive input PB0 (AIN0) and
negative input PB1 (AIN1). When the voltage on the positive input PB0 (AIN0) is higher
than the voltage on the negative input PB1 (AIN1), the Analog Comparator Output
(ACO) is set (one). The comparator can trigger a separate interrupt exclusive to the ana-
log comparator. The user can select interrupt triggering on comparator output rise, fall or
toggle. A block diagram of the comparator and its surrounding logic is shown in Figure
36.
Figure 36. Analog Comparator Block Diagram
• Bit 7 – ACD: Analog Comparator Disable
When this bit is set (one), the power to the analog comparator is switched off. This bit
can be set at any time to turn off the analog comparator. When changing the ACD bit,
the Analog Comparator Interrupt must be disabled by clearing the ACIE bit in ACSR.
Otherwise, an interrupt can occur when the bit is changed. To use the analog compara-
tor, the user must clear this bit.
• Bit 6 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny28 and will always read as zero.
• Bit 5 – ACO: Analog Comparator Output
ACO is directly connected to the comparator output.
• Bit 4 – ACI: Analog Comparator Interrupt Flag
This bit is set (one) when a comparator output event triggers the interrupt mode defined
by ACI1 and ACI0. The Analog Comparator Interrupt routine is executed if the ACIE bit
is set (one) and the I-bit in SREG is set (one). ACI is cleared by hardware when execut-
Bit
$08
Read/Write
Initial Value
PB0
PB1
ACD
R/W
7
1
R
6
–
0
ACO
R
X
5
R/W
ACI
4
0
ACIE
R/W
3
0
R
2
–
0
ACIS1
R/W
1
0
ACIS0
R/W
0
0
1062F–AVR–07/06
ACSR