ATtiny44A Atmel Corporation, ATtiny44A Datasheet - Page 65

• Manufacturer Part Number: ATtiny44A
• Manufacturer: Atmel Corporation

Specifications of ATtiny44A

• Flash (kbytes): 4 Kbytes
• Pin Count: 14
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 6
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 12
• Ext Interrupts: 12
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Eeprom (bytes): 256
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

8183D–AVR–04/11
• Port B, Bit 3 – RESET/dW/PCINT11
Table 10-8 on page 65
overriding signals shown in
Table 10-8.
1.
2.
Signal
Name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
PTOE
DIEOE
DIEOV
DI
AIO
• RESET: External Reset input is active low and enabled by unprogramming (“1”) the
• dW: When the debugWIRE Enable (DWEN) Fuse is programmed and Lock bits are
• PCINT11: Pin Change Interrupt source 11. The PB3 pin can serve as an external interrupt
RSTDISBL Fuse. Pullup is activated and output driver and digital input are deactivated when
the pin is used as the RESET pin.
unprogrammed, the debugWIRE system within the target device is activated. The RESET
port pin is configured as a wire-AND (open-drain) bi-directional I/O pin with pull-up enabled
and becomes the communication gateway between target and emulator.
source for pin change interrupt 1.
RSTDISBL is 1 when the Fuse is “0” (Programmed).
DebugWIRE is enabled when DWEN Fuse is programmed and Lock bits are unprogrammed.
PB3/RESET
RSTDISBL
1
RSTDISBL
DEBUGWIRE_ENABLE
Transmit
RSTDISBL
0
0
RSTDISBL
PCINT11 • PCIE1
DEBUGWIRE_ENABLE
PCINT11 • PCIE1)
dW/PCINT11 Input
Overriding Signals for Alternate Functions in PB[3:2]
(1)
(1)
(1)
(1)
/dW/
and
+ DEBUGWIRE_ENABLE
+ DEBUGWIRE_ENABLE
+ DEBUGWIRE_ENABLE
+ DEBUGWIRE_ENABLE
PCINT11
Figure 10-5 on page
Table 10-9 on page 66
(2)
(2)
+ (RSTDISBL
• debugWire
(2)
(2)
(2)
(2)
(1)
58.
+
•
relate the alternate functions of Port B to the
PB2/INT0/OC0A/CKOUT/PCINT10
CKOUT
0
CKOUT
1
CKOUT + OC0A enable
CKOUT • System Clock + CKOUT • OC0A
0
PCINT10 • PCIE1 + INT0
PCINT10 • PCIE1 + INT0
INT0/PCINT10 Input
ATtiny24A/44A/84A
65