ATtiny461 Atmel Corporation, ATtiny461 Datasheet - Page 99

• Manufacturer Part Number: ATtiny461
• Manufacturer: Atmel Corporation

Specifications of ATtiny461

• Flash (kbytes): 4 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Eeprom (bytes): 256
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

12.7.1
12.8
12.8.1
2588E–AVR–08/10
Modes of Operation
Compare Output Mode and Waveform Generation
Normal Mode
The design of the Output Compare Pin Configuration logic allows initialization of the OC1x state
before the output is enabled. Note that some COM1x1:0 bit settings are reserved for certain
modes of operation. For Output Compare Pin Configurations refer to
Table 12-3 on page
105, and
The Waveform Generator uses the COM1x1:0 bits differently in Normal mode and PWM modes.
For all modes, setting the COM1x1:0 = 0 tells the Waveform Generator that no action on the
OCW1x Output is to be performed on the next Compare Match. For compare output actions in
the non-PWM modes refer to
on page
A change of the COM1x1:0 bits state will have effect at the first Compare Match after the bits are
written. For non-PWM modes, the action can be forced to have immediate effect by using the
FOC1x strobe bits.
The mode of operation, i.e., the behavior of the Timer/Counter and the Output Compare pins, is
defined by the combination of waveform generation mode bits (PWM1A, PWM1B, and
WGM11:10) and compare output mode bits (COM1x1:0). The Compare Output mode bits do not
affect the counting sequence, while the Waveform Generation mode bits do. The COM1x1:0 bits
control whether the PWM output generated should be inverted, non-inverted or complementary.
For non-PWM modes the COM1x1:0 bits control whether the output should be set, cleared, or
toggled at a Compare Match.
The simplest mode of operation is Normal mode (PWM1A/PWM1B = 0), where the counter
counts from BOTTOM to TOP (defined as OCR1C) then restarts from BOTTOM. The OCR1C
defines the TOP value for the counter, hence also its resolution, and allows control of the Com-
pare Match output frequency. In toggle Compare Output Mode the Waveform Output (OCW1x)
is toggled at Compare Match between TCNT1 and OCR1x. In non-inverting Compare Output
Mode the Waveform Output is cleared on the Compare Match. In inverting Compare Output
Mode the Waveform Output is set on Compare Match. The timing diagram for Normal mode is
shown in
Figure 12-11. Normal Mode, Timing Diagram
OCWnx
(COMnx=1)
TCNTn
Period
112, and for the Phase and Frequency Correct PWM refer to
Table 12-7 on page
Figure
12-11.
102,
1
Table 12-4 on page
106.
Table 12-8 on page
2
104,
3
112. For fast PWM mode, refer to
Table 12-5 on page
4
Table 12-10 on page
Table 12-2 on page
105,
TOVn Interrupt Flag Set
OCnx Interrupt Flag Set
Table 12-6 on page
Table 12-9
100,
113.
99