ATtiny88 Automotive Atmel Corporation, ATtiny88 Automotive Datasheet - Page 209

• Manufacturer Part Number: ATtiny88 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATtiny88 Automotive

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 28
• Ext Interrupts: 28
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

T
Notes:
9157B–AVR–01/10
A
Symbol
I
Vacio
Iaclk
CC
= -40 C to 125 C, V
1. All DC Characteristics contained in this data sheet are based on actual silicon characterization of
2. Although each I/O port can sink more than the test conditions (10 mA at V
3. High Sink I/O pins are PD0, PD1, PD2 and PD3.
4. Although each I/O port can source more than the test conditions (10 mA at V
5. Measured with all I/O modules turned off (PRR = 0xFF).
6. Measured with Brown-Out Detection (BOD) disabled.
trollers manufactured in corner run process technology.
under steady state conditions (non-transient), the following must be observed:
• The sum of all I
• The sum of all I
If I
than the listed test condition.
under steady state conditions (non-transient), the following must be observed:
• The sum of all I
• The sum of all I
If II
greater than the listed test condition.
Parameter
Supply Current,
Active Mode
Supply Current,
Idle Mode
Supply Current,
Power-Down Mode
Analog Comparator Input
Offset Voltage (Absolute
Value)
Analog Comparator Input
Leakage Current
OL
OH
exceeds the test condition, V
exceeds the test condition, V
(5)
CC
(5)
= 2.7V to 5.5V (unless otherwise noted)
OL
OL
OH
OH
, for ports A0, A3, B0
, for ports A1
, for ports A2
, for ports A0
(6)
Condition
8MHz, Vcc = 3.0v
8MHz, Vcc = 5.0v
16MHz, Vcc = 5.0v
8MHz, Vcc = 3.0v
8MHz, Vcc = 5.0v
16MHz, Vcc = 5.0v
WDT enabled, V
WDT enabled, V
WDT disabled, V
WDT disabled, V
0.4v < Vin < Vcc-0.5
Vcc = 5v Vin = Vcc/2
–
–
–
OL
A2, C0
OH
A3, B0
A1, C0
may exceed the related specification. Pins are not guaranteed to sink current greater
may exceed the related specification. Pins are not guaranteed to source current
–
–
–
–
B7, C7, D5
C6, D0
B7, C6, D0
C5, C7 should not exceed 100 mA.
CC
CC
CC
CC
= 3V
= 5V
= 3V
= 5V
–
D4 should not exceed 100 mA.
–
–
D7 should not exceed 100 mA.
D7 should not exceed 100 mA.
(1)
Min
-50
(Continued)
CC
CC
= 5V, 5 mA at V
ATtiny88 Automotive
= 5V, 5mA at V
Typ
1.2
4.4
0.5
1.0
2.0
12
10
8
6
4
6
CC
CC
= 3V, 2 mA at V
Max
+50
ATtiny88
0.7
1.5
3.0
= 3V, 2 mA at V
12
44
66
20
30
40
4
8
AVR micro-con-
CC
Units
CC
mA
mA
mA
mA
mA
mA
mV
µA
µA
µA
µA
nA
= 2.7V)
= 2.7V)
209