SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 21

• Manufacturer Part Number: SAM3U2C
• Manufacturer: Atmel Corporation

Specifications of SAM3U2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

5.5.4
Table 5-1.
Notes:
6430ES–ATARM–22-Aug-11
Mode
Backup
Mode
Wait
Mode
Sleep
Mode
1. When considering wake-up time, the time required to start the PLL is not taken into account. Once started, the device works
2. The external loads on PIOs are not taken into account in the calculation.
3. BOD current consumption is not included.
4. Current consumption on VDDBU.
5. 8 µA total current consumption - without using internal voltage regulator.
6. Depends on MCK frequency.
7. In this mode the core is supplied and not clocked but some peripherals can be clocked.
Registers,
Oscillator
RTC RTT
(VDDBU
Region)
Backup
SUPC,
32 kHz
Low Power Mode Summary Table
POR
with the 4/8/12 MHz Fast RC oscillator. The user has to add the PLL start-up time if it is needed in the system. The wake-up
time is defined as the time taken for wake up until the first instruction is fetched.
15 µA total current consumption - using internal voltage regulator.
ON
ON
ON
Low Power Mode Configuration Summary
Regulator
SHDN =0
SHDN =1
SHDN =1
OFF
ON
ON
The modes detailed above are the main low power modes. Each part can be set to on or off sep-
arately and wake up sources can be individually configured.
of the configurations of the low power modes.
(Not powered)
Peripherals
(Not clocked)
(Not clocked)
Powered
Memory
Powered
Core
OFF
(7)
+SLEEPDEEP
+SLEEPDEEP
+SLEEPDEEP
+LPM bit = 1
+LPM bit = 0
Mode Entry
WFE or WFI
bit = 1
bit = 0
bit = 0
WFE
WFE
FWUP pin
WKUP0-15 pins
BOD alarm
RTC alarm
RTT alarm
Any Event from: Fast
startup through
WKUP0-15 pins
RTC alarm
RTT alarm
USB wake-up
Entry mode =WFI
Interrupt Only; Entry
mode =WFE Any
Enabled Interrupt
and/or Any Event
from: Fast start-up
through WKUP0-15
pins
RTC alarm
RTT alarm
USB wake-up
Potential Wake Up
Sources
Reset
Clocked
back
Clocked
back
Wake Up
Core at
Previous
state saved
Previous
state saved
Previous
state saved
while in Low
Power Mode
PIO State
Table 5-1
PIOA &
PIOB &
PIOC
Inputs with
pull ups
Unchanged 8 µA/15 µA
Unchanged
at Wake Up
PIO State
SAM3U Series
below shows a summary
2.5 µA typ
(6)
Consumption
(2) (3)
(4)
(5)
< 0.5 ms
< 10 µs
(6)
Wake-up
Time
(1)
21