SAM9G35 Atmel Corporation, SAM9G35 Datasheet - Page 473

• Manufacturer Part Number: SAM9G35
• Manufacturer: Atmel Corporation

Specifications of SAM9G35

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 105
• Ext Interrupts: 105
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 3
• Uart: 6
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

31. DMA Controller (DMAC)
31.1
31.2
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
Description
Embedded Characteristics
The DMA Controller (DMAC) is an AHB-central DMA controller core that transfers data from a
source peripheral to a destination peripheral over one or more AMBA buses. One channel is
required for each source/destination pair. In the most basic configuration, the DMAC has one
master interface and one channel. The master interface reads the data from a source and writes
it to a destination. Two AMBA transfers are required for each DMAC data transfer. This is also
known as a dual-access transfer.
The DMAC is programmed via the APB interface.
The DMAC embeds 8 channels.
• Two DMACs
• DMAC0 is full featured and optimized for memory-to-memory transfers thanks to the 64-word
• DMAC1 is optimized for peripheral-to-memory transfers, without PIP support
• Acting as Two Matrix Masters
• Embeds 8 unidirectional channels with programmable priority
• Address Generation
• Channel Buffering
• Channel Control
FIFO on channel 0
– Source/Destination address programming
– Address increment, decrement or no change
– DMA chaining support for multiple non-contiguous data blocks through use of linked
– Scatter support for placing fields into a system memory area from a contiguous
– Gather support for extracting fields from a system memory area into a contiguous
– User enabled auto-reloading of source, destination and control registers from initially
– Auto-loading of source, destination and control registers from system memory at end
– Unaligned system address to data transfer width supported in hardware
– Picture-In-Picture Mode (on DMAC0 only)
– 16-word FIFO (64-word for channel 0 of DMAC0)
– Automatic packing/unpacking of data to fit FIFO width
– Programmable multiple transaction size for each channel
– Support for cleanly disabling a channel without data loss
– Suspend DMA operation
– Programmable DMA lock transfer support
lists
transfer. Writing a stream of data into non-contiguous fields in system memory
transfer
programmed values at the end of a block transfer
of block transfer in block chaining mode
SAM9G35
SAM9G35
473
473