SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 721
SAM9XE512
Manufacturer Part Number
SAM9XE512
Description
Manufacturer
Atmel Corporation
Datasheets
1.SAM9260.pdf
(290 pages)
2.SAM9261.pdf
(248 pages)
3.SAM9XE128.pdf
(860 pages)
4.SAM9XE128.pdf
(48 pages)
Specifications of SAM9XE512
Flash (kbytes)
512 Kbytes
Pin Count
217
Max. Operating Frequency
180 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
96
Ext Interrupts
96
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
2
Uart
6
Ssc
1
Ethernet
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
Yes
Adc Channels
4
Adc Resolution (bits)
10
Adc Speed (ksps)
312
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.65 to 1.95
Fpu
No
Mpu / Mmu
No / Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- SAM9260 PDF datasheet
- SAM9261 PDF datasheet #2
- SAM9XE128 PDF datasheet #3
- SAM9XE128 PDF datasheet #4
- Current page: 721 of 860
- Download datasheet (13Mb)
39.5.2.9
39.5.2.10
39.5.2.11
721
AT91SAM9XE128/256/512 Preliminary
Transmit Data Cancellation
Endpoints Without Dual-Banks
Endpoints With Dual-Banks
Some endpoints have dual-banks whereas some endpoints have only one bank. The procedure
to cancel transmission data held in these banks is described below.
To see the organization of dual-bank availablity refer to
There are two possibilities: In one case, TXPKTRDY field in UDP_CSR has already been set. In
the other instance, TXPKTRDY is not set.
There are two possibilities: In one case, TXPKTRDY field in UDP_CSR has already been set. In
the other instance, TXPKTRDY is not set.
• TXPKTRDY is not set:
• TXPKTRDY has already been set:
• TXPKTRDY is not set:
• TXPKTRDY has already been set:
– Reset the endpoint to clear the FIFO (pointers). (See,
– Clear TXPKTRDY so that no packet is ready to be sent
– Reset the endpoint to clear the FIFO (pointers). (See,
– Reset the endpoint to clear the FIFO (pointers). (See,
– Clear TXPKTRDY and read it back until actually read at 0.
– Set TXPKTRDY and read it back until actually read at 1.
– Clear TXPKTRDY so that no packet is ready to be sent.
– Reset the endpoint to clear the FIFO (pointers). (See,
Endpoint
Endpoint
Endpoint
Endpoint
Register”.)
Register”.)
Register”.)
Register”.)
Table 39-1 ”USB Endpoint
Section 39.6.9 ”UDP Reset
Section 39.6.9 ”UDP Reset
Section 39.6.9 ”UDP Reset
Section 39.6.9 ”UDP Reset
6254C–ATARM–22-Jan-10
Description”.
Related parts for SAM9XE512
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: