AD7898 Analog Devices, AD7898 Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD7898
Manufacturer Part Number
AD7898
Description
5V, 12-Bit, Serial 220 kSPS ADC in a 8-Lead Package
Manufacturer
Analog Devices
Datasheet
1.AD7898.pdf
(16 pages)
Specifications of AD7898
Resolution (bits)
12bit
# Chan
1
Sample Rate
220kSPS
Interface
Ser
Analog Input Type
SE-Bip
Ain Range
Bip (Vref),Bip (Vref) x 4,Bip 10V,Bip 2.5V
Adc Architecture
SAR
Pkg Type
SOIC
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD7898AR-10
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7898ARZ-10
Manufacturer:
AMI
Quantity:
6 218
Part Number:
AD7898ARZ-10
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7898ARZ-3
Manufacturer:
ADI/亚德诺
Quantity:
20 000
To enter power-down, the conversion process must be inter-
rupted by bringing CS high anywhere after the fourth falling
edge of SCLK and before the 11th falling edge of SCLK as
shown in Figure 11. Once CS has been brought high in this
window of SCLK, then the part will enter power-down and the
conversion that was initiated by the falling edge of CS will be
terminated and SDATA will go back into three-state.
In order to exit this mode of operation and power the AD7898
up again, a dummy conversion is performed. On the falling edge
of CS the device will begin to power up, and will continue to
power up as long as CS is held low until after the falling edge of
the 11th SCLK. The device will be fully powered up once 16
SCLKs have elapsed and valid data will result from the next
conversion as shown in Figure 12. If CS is brought high before
the 11th falling edge of SCLK, the AD7898 will go back into
power-down. This avoids accidental power-up due to glitches
on the CS line or an inadvertent burst of eight SCLK cycles
while CS is low. So although the device may begin to power up
on the falling edge of CS, it will power down again on the rising
edge of CS as long as it occurs before the 11th SCLK falling edge.
Power-Up Times
The power-up time of the AD7898 is typically 4.33 µs, which
means that with any frequency of SCLK up to 3.7 MHz, one
dummy cycle will always be sufficient to allow the device to
power up. Once the dummy cycle is complete, the ADC will be
fully powered up and the input signal will be properly acquired.
The quiet time, t
which the bus goes back into three-state after the dummy con-
version, to the next falling CS edge.
When powering up from power-down mode at any SCLK fre-
quency a dummy cycle is sufficient to power up the device and
fully acquire V
cycle of 16 SCLKs must always elapse to power up the device
and fully acquire V
the device and fully acquire V
frequency was applied to the ADC, the cycle time would be 16 µs.
REV. A
IN
; it does not necessarily mean that a full dummy
QUIET
SDATA
IN
SCLK
. 4.33 µs would be sufficient to power up
CS
, must still be allowed from the point at
SDATA
SCLK
CS
IN
1
. If, for example, a 1 MHz SCLK
THE PART BEGINS
TO POWER UP
Figure 11. Entering Power-Down when in Mode 1
Figure 12. Exiting Power-Down when in Mode 1
INVALID DATA
1
2
3
11
4
16
–13–
In one dummy cycle, 16 µs, the part would be powered up and
V
just over four SCLK cycles would have elapsed. At this stage the
ADC would be fully powered up and the signal acquired. So, in
this case, CS could be brought high after the 11th SCLK falling
edge and brought low again after t
MICROPROCESSOR/MICROCONTROLLER INTERFACE
FOR MODE 0 OPERATION
The AD7898 provides a 3-wire serial interface that can be
used for connection to the serial ports of DSP processors and
microcontrollers. Figures 13 through 16 show the AD7898
interfaced to a number of different microcontrollers and DSP
processors. The AD7898 accepts an external serial clock and,
as a result, in all interfaces shown here, the processor/controller
is configured as the master, providing the serial clock with the
AD7898 configured as the slave in the system. The AD7898 has
no BUSY signal, therefore a read operation should be timed to
occur 3.3 µs after CONVST goes low.
8x51/L51 to AD7898 Interface
Figure 13 shows an interface between the AD7898 and the
8x51/L51 microcontroller. The 8x51/L51 is configured for its
Mode 0 serial interface mode. The diagram shows the simplest
form of the interface where the AD7898 is the only part con-
nected to the serial port of the 8x51/L51 and, therefore, no
decoding of the serial read operations is required.
IN
fully acquired. However, after 4.33 µs with a 1 MHz SCLK
1
THREE-STATE
11
Figure 13. 8x51/L51 to AD7898 Interface
8x51/L51
THE PART IS FULLY
P3.0
P3.1
POWERED UP
VALID DATA
16
QUIET
to initiate a new conversion.
16
SDATA
SCLK
AD7898
AD7898