MAX13325GUI/V+T Maxim Integrated Products, MAX13325GUI/V+T Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX13325GUI/V+T
Manufacturer Part Number
MAX13325GUI/V+T
Description
IC AUD LINE DVR DL AUTO 28TSSOP
Manufacturer
Maxim Integrated Products
Type
Line Driver, Transmitterr
Datasheet
1.MAX13325GUIV.pdf
(21 pages)
Specifications of MAX13325GUI/V+T
Applications
Automotive Audio
Mounting Type
Surface Mount
Package / Case
28-TSSOP Exposed Pad, 28-eTSSOP, 28-HTSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
When in diagnostic mode with mute enabled, if there
is excessive offset on any output, the MAX13325/
MAX13326 reports the condition through the I
face and the FLAG output. See Table 14.
When in diagnostic mode, if any of the output pairs is
excessively loaded, the MAX13325/MAX13326 issue a
warning and report the condition through the I
face and the FLAG output. The faulted channel is not
switched off. See Table 15.
Table 14. Excessive Offset Diagnostic
Table 15. Overcurrent Diagnostic
Table 16. Open-Load Diagnostic
Overcurrent on Right
FAULT CONDITION
FAULT CONDITION
FAULT CONDITION
Right-Channel Open
Overcurrent on Left
Left-Channel Open
Excessive Output
Excessive Output
Offset on Right
Offset on Left
Channel
Channel
Channel
Channel
Load
Load
______________________________________________________________________________________
OFFSETR bit is set in the RFAULT
OFFSETL bit is set in the LFAULT
OPENR bit is set in the RFAULT
OPENL bit is set in the LFAULT
LIMITR bit is set in the RFAULT
LIMITL bit is set in the LFAULT
FLAG bit set. See Table 7.
FLAG bit set. See Table 7.
FLAG bit set. See Table 7.
FLAG bit set. See Table 7.
FLAG bit set. See Table 7.
Dual Automotive, Audio Line Drivers
FLAG is asserted low.
FLAG is asserted low.
FLAG is asserted low.
FLAG is asserted low.
FLAG is asserted low.
FLAG is asserted low.
register. See Table 5.
register. See Table 6.
register. See Table 5.
register. See Table 6.
register. See Table 5.
register. See Table 6.
STATUS REPORT
STATUS REPORT
STATUS REPORT
FLAG bit set.
Excessive Offset
with I
Overcurrent
2
2
C inter-
C inter-
2
C Control and Diagnostic
In the LMASK register, set
In the RMASK register, set
set MOPENL bit to 1. See
set MOPENR bit to 1. See
set MLIMITL bit to 1. See
set MLIMITR bit to 1. See
MOFFSETR bit to 1. See
MOFFSETL bit to 1. See
In the RMASK register,
In the RMASK register,
In the LMASK register,
In the LMASK register,
When in diagnostic mode and the open-load detec-
tion is initiated, the selected channel is switched off for
1ms during which the diagnosis is taking place. Upon
detecting an open load on any channel, the MAX13325/
MAX13326 report the condition using the I
and the FLAG output. See Table 16.
When in diagnostic mode, if the MAX13325/MAX13326
exceed the V
during a load-dump condition), the device reports the
condition using the I
See Table 17.
UNMASK
UNMASK
UNMASK
Table 10.
Table 10.
Table 10.
Table 9.
Table 9.
Table 9.
DD
overvoltage threshold (for example
2
C interface and the FLAG output.
Cleared on reading the RFAULT
Cleared on reading the RFAULT
Cleared on reading the LFAULT
Cleared on reading the LFAULT
Load current falls below the
Load current falls below the
current-limit threshold.
current-limit threshold.
the RFAULT register.
the LFAULT register.
Cleared on reading
Cleared on reading
RECOVERY
RECOVERY
RECOVERY
register.
register.
register.
register.
Overvoltage
2
Open Load
C interface
15