TDA8922B NXP Semiconductors, TDA8922B Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
TDA8922B
Manufacturer Part Number
TDA8922B
Description
The TDA8922B is a high efficiency class-D audio power amplifier with very lowdissipation
Manufacturer
NXP Semiconductors
Datasheet
1.TDA8922B.pdf
(32 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TDA8922BJ
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
TDA8922BTH
Manufacturer:
NXP
Quantity:
11
Part Number:
TDA8922BTH
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
TDA8922BTH/N2
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
TDA8922BU/N2
Manufacturer:
NXP
Quantity:
152 970
Part Number:
TDA8922BU/N2
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
16. Soldering
9397 750 13357
Preliminary data sheet
16.2.1 Soldering by dipping or by solder wave
16.2.2 Manual soldering
16.3.1 Reflow soldering
16.1 Introduction
16.2 Through-hole mount packages
16.3 Surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account of
soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages
(document order number 9398 652 90011).
There is no soldering method that is ideal for all IC packages. Wave soldering is often
preferred when through-hole and surface mount components are mixed on one
printed-circuit board. Wave soldering can still be used for certain surface mount ICs, but it
is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended.
Driven by legislation and environmental forces the worldwide use of lead-free solder
pastes is increasing.
Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 C
or 265 C, depending on solder material applied, SnPb or Pb-free respectively.
The total contact time of successive solder waves must not exceed 5 seconds.
The device may be mounted up to the seating plane, but the temperature of the plastic
body must not exceed the specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling may be necessary immediately
after soldering to keep the temperature within the permissible limit.
Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the
seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is
less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is
between 300 C and 400 C, contact may be up to 5 seconds.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 seconds and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 C to 270 C depending on solder paste
material. The top-surface temperature of the packages should preferably be kept:
•
below 225 C (SnPb process) or below 245 C (Pb-free process)
– for all BGA, HTSSON..T and SSOP..T packages
Rev. 01 — 1 October 2004
2
50 W class-D power amplifier
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
TDA8922B
stg(max)
). If the
28 of 32