P8XC557E4 NXP Semiconductors, P8XC557E4 Datasheet - Page 45
P8XC557E4
Manufacturer Part Number
P8XC557E4
Description
The P80C557E4/P83C557E4/P89C557E4 (hereafter generically referred to as P8xC557E4) single-chip 8-bit microcontroller is manufactured in an advanced CMOS process and is a derivative of the 80C51 microcontroller family
Manufacturer
NXP Semiconductors
Datasheet
1.P8XC557E4.pdf
(72 pages)
- Current page: 45 of 72
- Download datasheet (375Kb)
Philips Semiconductors
6.13.4 Seconds Timer
This counter provides an overflow signal every second, when the
32kHz oscillator is running.
The overflow output sets the interrupt flag SECINT. This interrupt
can be disabled/enabled by ENSECI. If SECINT is enabled, it is
logically ORed with INT1 (external interrupt 1).
Seconds interrupt and INT1 therefor share the same priority and
vector. The software has to check both flags SECINT (PLLCON.5)
and IE1 (TCON.3), to distinguish between the two interrupt sources.
SECINT can only be cleared via writing a ‘0’ to this bit .
The external interrupts INT0 , INT1 or the seconds interrupt can
Wake-up the PLL oscillator and the microcontroller as described in
chapter “Wake-up from Power-down Mode”.
For a Wake-up via INT1 or seconds interrupt, IE1 must be enabled
and level-sensitive.
A further function of the seconds timer is to control the start-up
timing of the microcontroller after Reset or after Wake-up from
1999 Mar 02
Single-chip 8-bit microcontroller
XTAL4
RSTIN
C
RUN32 PD
32.768 KHz
1
32 kHz
Oscil-
lator
R
f
C
2
Figure 45. Block diagram PLL
SECONDS TIMER
XTAL3
Phase
comparator
45
Stretched
Reset
P83C557E4/P80C557E4/P89C557E4
Programmable
divider
Power-down. It controls the stretching of the reset pulse to the
microcontroller and controls releasing the system clock to the
microcontroller.
A RSTIN signal of 1us at minimum will reset the microcontroller.
In case of Reset or Wake-up with halted 32kHz oscillator: From
RSTIN falling edge or Wake-up interrupt it takes 560ms at maximum
for the start-up of the 32kHz oscillator itself and the stabilization of
the PLL’s.
In case of Wake-up with running 32kHz oscillator: From Wake-up
interrupt it takes about 1ms for the stabilization of the PLL’s.
After this start-up time, the microcontroller is supplied with the
system clock and – in case of a reset – the internally stretched reset
signal overlaps about 45us, to guarantee a proper initialization of the
microcontroller.
For further information refer to section 6.11 Power reduction modes .
Loop
filter
Internal Bus
PLLCON
CCO
PD
PD = power down
system clock
Reset to controller
’Seconds’
Interrupt
request
Product specification
Related parts for P8XC557E4
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: