XA-C3 NXP Semiconductors, XA-C3 Datasheet - Page 15
![The XA-C3 is a member of the Philips XA (eXtended Architecture) family of high-performance 16-bit single-chip microcontrollers](/photos/41/53/415313/sot389-1_3d_sml.gif)
XA-C3
Manufacturer Part Number
XA-C3
Description
The XA-C3 is a member of the Philips XA (eXtended Architecture) family of high-performance 16-bit single-chip microcontrollers
Manufacturer
NXP Semiconductors
Datasheet
1.XA-C3.pdf
(68 pages)
1. All active–low signals are indicated by a “/” symbol.
Philips Semiconductors
NOTE:
2000 Jan 25
ALE ; PROG/
XA 16-bit microcontroller family
32K/1024 OTP CAN transport layer controller
1 UART, 1 SPI Port, CAN 2.0B, 32 CAN ID filters, transport layer co-processor
MNEMONIC
EA/ ; WAIT ;
CAN RxD
CAN TxD
PSEN/
XTAL1
XTAL2
RST/
P3.4
P3.5
P3.6
P3.7
V
PP
PLCC
PIN NUMBERS
16
17
18
19
10
33
32
35
12
34
21
20
LQFP
10
11
12
13
27
26
29
28
15
14
4
6
TYPE
I/O
I/O
I/O
O
O
O
O
O
I
I
I
I
T0: Timer 0 External count input or Timer 0 Overflow output.
T1 : Timer 1 External count input or Timer 1 Overflow output.
WRL/: External DATA memory Low Byte Write Strobe.
RD/: External DATA memory Read Strobe.
RESET/:
NOTE:
10. A low on this pin resets the XA–C3, causing I/O Ports and peripherals to take on
Refer to the Reset section for details.
Address Latch Enable ; Program Pulse/:
NOTES:
11. A high output on the ALE pin signals External circuitry to latch the address portion of
12. A pulse on ALE occurs only when needed to process an External bus cycle. During
Program Store Enable/:
This is the Read Strobe for External PROGRAM memory.
NOTES:
13. When the microcontroller accesses External PROGRAM memory, PSEN/ is driven
14. PSEN/ is only active when External code accesses are performed.
External Access/ ; WAIT ; Programming Supply Voltage:
NOTES:
15. The EA/ input determines whether the internal PROGRAM memory of the XA–C3 is
16. The EA/ pin is latched as the (External) Reset input is released and its value applied
17. After Reset is released, this pin takes on the function of a Bus WAIT input. If WAIT
18. During EPROM programming, this pin is also the programming supply voltage input.
CAN Receive Data input: CAN serial receiver input to the SJA1000 PeliCAN core.
CAN Transmit Data output: CAN serial transmitter output from the SJA1000 PeliCAN
core.
Crystal 1: Input to the inverting amplifier used in the oscillator circuit and input to the
internal clock generator circuits.
Crystal 2: Output from the oscillator amplifier.
their default states, and the processor to begin execution at the Address contained in
the Reset Vector.
the multiplexed Address/DATA bus.
EPROM programming, this pin is used as the Program pulse input.
low in order to enable memory devices.
used for code execution.
during later execution. When latched as a 0, External PROGRAM memory is used
exclusively. When latched as a 1, internal PROGRAM memory will be used up to its
limit, and External PROGRAM memory is used above that point.
is asserted High during any External bus access, that cycle will be extended until
WAIT is released.
8
NAME AND FUNCTION
Preliminary specification
XA-C3