STM8L152C8 STMicroelectronics, STM8L152C8 Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STM8L152C8
Manufacturer Part Number
STM8L152C8
Description
STM8L-Ultra Low Power-8 bits Microcontrollers
Manufacturer
STMicroelectronics
Datasheet
1.STM8L151R6.pdf
(126 pages)
Specifications of STM8L152C8
Operating Power Supply
1.65 to 3.6 V (without BOR), 1.8 to 3.6 V (with BOR)
Temp. Range
−40 to 85, 105 or 125 °C
5 Low Power Modes
Wait, Low power run (5.9 μA), Low power wait (3 μA), Active-halt with full RTC (1.4 μA), Halt (400 nA)
Dynamic Power Consumption
200 μA/MHz+330 μA
Ultra Low Leakage Per I/0
50 nA
Max Freq
16 MHz, 16 CISC MIPS peak
Lcd
8x40 or 4x44 w/ step-up converter
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STM8L152C8T6
Manufacturer:
STM
Quantity:
520
Company:
Part Number:
STM8L152C8T6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Company:
Part Number:
STM8L152C8U6
Manufacturer:
ST
Quantity:
75
Company:
Part Number:
STM8L152C8U6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Pin description
Table 5.
28/126
10 6
11 7
1
2
3
4
6
7
8
9
number
Pin
2
3
4
5
-
-
-
-
2 NRST/PA1
3
4
5
6
7
- PH0/LCD SEG 36
- PH1/LCD SEG 37
- PH2/LCD SEG 38
- PH3/LCD SEG 39
PA2/OSC_IN/
[USART1_TX]
[SPI1_MISO]
PA3/OSC_OUT/[USART1
_RX]
PA4/TIM2_BKIN/
[TIM2_ETR]
LCD_COM0
COMP1_INP
PA5/TIM3_BKIN/
[TIM3_ETR]
LCD_COM1
COMP1_INP
PA6/ADC1_TRIG/
LCD_COM2
COMP1_INP
Table 4.
High density and medium+ density STM8L15x pin description
Type
Level
Port and control
configuration
Reset state
(2)
/[SPI1_MOSI]
Pin name
(1)
(2)
(2)
(3)
(3)
(3)
(2)
(2)
/
/ADC1_IN2
/ADC1_IN1/
/ADC1_IN0/
Legend/abbreviation
/
(3)
(3)
(3)
(3)
(2)
I= input, O = output, S = power supply
FT: Five-volt tolerant
Output
Input
Output
Bold X (pin state after reset release).
Unless otherwise specified, the pin state is the same during the reset phase (i.e.
“under reset”) and after internal reset release (i.e. at reset state).
I/O FT
I/O FT
I/O FT
I/O FT
I/O
I/O
I/O
I/O FT
I/O FT
I/O FT
HS = high sink/source (20 mA)
float = floating, wpu = weak pull-up
T = true open drain, OD = open drain, PP = push pull
(5)
(5)
(5)
(5)
(5)
(5)
(5)
Doc ID 17943 Rev 4
X
X
X
X
X
X
X
X
X
Input
X
X
X
X
X
X
X
X
X
X
X HS X
X HS X
X HS X
X HS X
X HS X
X HS X
X HS X
X HS X
X HS X
HS X
Output
X Port H0 LCD segment 36
X Port H1 LCD segment 37
X Port H2 LCD segment 38
X Port H3 LCD segment 39
X Reset
X Port A2
X Port A3
X Port A4
X Port A5
X Port A6
STM8L15xx8, STM8L15xR6
PA1
HSE oscillator input /
[USART1 transmit] / [SPI1
master in- slave out] /
HSE oscillator output /
[USART1 receive]/ [SPI1
master out/slave in]/
Timer 2 - break input /
/[Timer 2 - trigger] /
LCD COM 0 / ADC1 input
2/Comparator 1 positive
input
Timer 3 - break input /
[Timer 3 - trigger] /
LCD_COM 1 /
ADC1 input 1/Comparator 1
positive input
ADC1 - trigger / LCD_COM2
/ ADC1 input 0/Comparator
1 positive input
Default alternate function