ST72321J7-Auto STMicroelectronics, ST72321J7-Auto Datasheet - Page 133
ST72321J7-Auto
Manufacturer Part Number
ST72321J7-Auto
Description
8-bit MCU for automotive with 48 Kbyte Flash, 10-bit ADC, timers, SPI, SCI and I2C interfaces
Manufacturer
STMicroelectronics
Datasheet
1.ST72321R9-AUTO.pdf
(243 pages)
Specifications of ST72321J7-Auto
Hdflash Endurance
100 cycles, data retention 20 years
Clock Sources
crystal/ceramic resonator oscillators, internal RC oscillator and bypass for external clock
4 Power Saving Modes
Halt, Active Halt, Wait and Slow
- Current page: 133 of 243
- Download datasheet (3Mb)
ST72321xx-Auto
14.8.3
Note:
Table 68.
Data I/O register (SPIDR)
The SPIDR register is used to transmit and receive data on the serial bus. In a master
device, a write to this register will initiate transmission/reception of another byte.
During the last clock cycle the SPIF bit is set, a copy of the received data byte in the shift
register is moved to a buffer. When the user reads the serial peripheral data I/O register, the
buffer is actually being read.
While the SPIF bit is set, all writes to the SPIDR register are inhibited until the SPICSR
register is read.
SPIDR
Bit
4
3
2
1
0
7
MODF
Name
SOD
SSM
SSI
-
SPICSR register description (continued)
Mode Fault flag
Reserved, must be kept cleared
SPI Output Disable
SS Management
SS Internal Mode
This bit is set by hardware when the SS pin is pulled low in master mode (see
Master mode fault (MODF) on page
SPIE = 1 in the SPICSR register. This bit is cleared by a software sequence (An
access to the SPICR register while MODF = 1 followed by a write to the SPICR
register).
0: No master mode fault detected
1: A fault in master mode has been detected
This bit is set and cleared by software. When set, it disables the alternate function of
the SPI output (MOSI in master mode / MISO in slave mode).
0: SPI output enabled (if SPE = 1)
1: SPI output disabled
This bit is set and cleared by software. When set, it disables the alternate function of
the SPI SS pin and uses the SSI bit value instead. See
page
0: Hardware management (SS managed by external pin)
1: Software management (internal SS signal controlled by SSI bit. External SS pin
free for general-purpose I/O)
This bit is set and cleared by software. It acts as a ‘chip select’ by controlling the
level of the SS slave select signal when the SSM bit is set.
0: Slave selected
1: Slave deselected
6
123.
5
Doc ID 13829 Rev 1
4
D[7:0]
RW
Function
128). An SPI interrupt can be generated if
3
Serial peripheral interface (SPI)
2
Slave select management on
Reset value: Undefined
1
133/243
0
Related parts for ST72321J7-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-BIT MCU WITH NESTED INTERRUPTS, FLASH,10-BIT ADC, FIVE TIMERS, SPI, SCI, I2C INTERFACE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
8-bit Mcu With Nested Interrupts, Flash, 10-bit Adc, 5 Timers, Spi, Sci, I2c Interface
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet: