ST72321AR7 STMicroelectronics, ST72321AR7 Datasheet - Page 139

• Manufacturer Part Number: ST72321AR7
• Description: 8-BIT MCU WITH NESTED INTERRUPTS, FLASH,10-BIT ADC, FIVE TIMERS, SPI, SCI, I2C INTERFACE
• Manufacturer: STMicroelectronics

Specifications of ST72321AR7

• Hdflash Endurance: 100 cycles, data retention
• Clock Sources: crystal/ceramic resonator oscillators, internal RC oscillator, clock security system and bypass for external clock
• Four Power Saving Modes: Halt, Active-Halt,Wait and Slow
• Main Clock Controller With: Real time base, Beep and Clock-out capabilities
• Two 16-bit Timers With: 2 input captures, 2 output compares, external clock input on one timer, PWM and pulse generator modes
• 8-bit Pwm Auto-reload Timer With: 2 input captures, 4 PWM outputs, output compare and time base interrupt, external clock with event detector

12.2 ABSOLUTE MAXIMUM RATINGS
Stresses above those listed as “absolute maxi-
mum ratings” may cause permanent damage to
the device. This is a stress rating only and func-
tional operation of the device under these condi-
12.2.1 Voltage Characteristics
12.2.2 Current Characteristics
Notes:
1. Directly connecting the RESET and I/O pins to V
is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter).
To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7kΩ for
RESET, 10kΩ for I/Os). For the same reason, unused I/O pins must not be directly tied to V
2. I
respected, the injection current must be limited externally to the I
while a negative injection is induced by V
corresponding V
3. All power (V
4. Negative injection disturbs the analog performance of the device. See note in
For best reliability, it is recommended to avoid negative injection of more than 1.6mA.
5. When several inputs are submitted to a current injection, the maximum ΣI
and negative injected currents (instantaneous values). These results are based on characterisation with ΣI
mum current injection on four I/O port pins of the device.
6. True open drain I/O port pins do not accept positive injection.
|ΔV
INJ(PIN)
I
DDx
|V
INJ(PIN)
ΣI
V
V
V
V
V
SSA
Symbol
Symbol
ESD(HBM)
INJ(PIN)
DD
PP
ESD(MM)
IN
| and |ΔV
I
I
VDD
VSS
must never be exceeded. This is implicitly insured if V
I
1) & 2)
IO
- V
- V
- V
2) & 4)
DD
SS
SS
SSx
2)
IN
) and ground (V
|
SSx
maximum must always be respected
|
Supply voltage
Programming Voltage
Input Voltage on true open drain pin
Input voltage on any other pin
Variations between different digital power pins
Variations between digital and analog ground pins
Electro-static discharge voltage (Human Body Model)
Electro-static discharge voltage (Machine Model)
Total current into V
Total current out of V
Output current sunk by any standard I/O and control pin
Output current sunk by any high sink I/O pin
Output current source by any I/Os and control pin
Injected current on V
Injected current on RESET pin
Injected current on OSC1 and OSC2 pins
Injected current on PB0 (Flash devices only)
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
SS
) lines must always be connected to the external supply.
IN
<V
DD
SS
PP
SS
. For true open-drain pads, there is no positive injection current, and the
power lines (source)
Ratings
Ratings
pin
ground lines (sink)
DD
or V
5) & 6)
SS
could damage the device if an unintentional internal reset
tions is not implied. Exposure to maximum rating
conditions for extended periods may affect device
reliability.
INJ(PIN)
IN
maximum is respected. If V
3)
3)
ST72321Rx ST72321ARx ST72321Jx
value. A positive injection is induced by V
INJ(PIN)
5)
“ADC Accuracy” on page
see
is the absolute sum of the positive
V
Maximum value
Maximum value
SS
section 12.7.3 on page 155
V
-0.3 to V
SS
-0.3 to 6.5
DD
± 25
150
150
- 25
± 5
± 5
± 5
+ 5
± 5
25
50
6.5
13
50
50
or V
IN
DD
maximum cannot be
SS
+0.3
.
170.
INJ(PIN)
Unit
Unit
mA
mA
139/193
mV
IN
V
maxi-
>V
DD