DS80C390 Maxim, DS80C390 Datasheet - Page 39
![no-image](/images/no-image-200.jpg)
DS80C390
Manufacturer Part Number
DS80C390
Description
The DS80C390 is a fast 8051-compatible microprocessor with dual CAN 2
Manufacturer
Maxim
Datasheet
1.DS80C390.pdf
(53 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS80C390-FCR
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
DS80C390-FCR+
Manufacturer:
MAXIM
Quantity:
228
Company:
Part Number:
DS80C390-FCR+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
DS80C390-FNR
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
DS80C390-FNR+
Manufacturer:
MAXIM
Quantity:
59
Company:
Part Number:
DS80C390-FNR+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
DS80C390-QCR
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
DS80C390-QCR+
Manufacturer:
Maxim Integrated Products
Quantity:
135
Company:
Part Number:
DS80C390-QCR+
Manufacturer:
MAXIM
Quantity:
17
Company:
Part Number:
DS80C390QCR
Manufacturer:
MURATA
Quantity:
20 000
the microcontroller can never be operated faster than 40MHz. This means that the maximum crystal oscillator or
external clock source is 10MHz when using the 4X setting, and 20MHz when using the 2X setting.
The primary advantage of the clock multiplier is that it allows the microcontroller to use slower crystals to achieve
the same performance level. This reduces EMI and cost, as slower crystals are generally more available and thus
less expensive.
Table 11. System Clock Configuration
The system clock and machine cycle rate changes one machine cycle after the instruction changing the control
bits. Note that the change affects all aspects of system operation, including timers and baud rates. The use of the
switchback feature, described later, can eliminate many of the problems associated with the PMM.
Changing the System Clock/Machine Cycle Clock Frequency
The microcontroller incorporates a special locking sequence to ensure “glitch-free” switching of the internal clock
signals. All changes to the CD1, CD0 bits must pass through the 10 (divide-by-4) state. For example, to change
from 00 (frequency multiplier) to 11 (PMM), the software must change the bits in the following sequence: 00 ≥ 10 ≥
11. Attempts to switch between invalid states will fail, leaving the CD1, CD0 bits unchanged.
The following sequence must be followed when switching to the frequency multiplier as the internal time source.
This sequence can only be performed when the device is in divide-by-4 operation. The steps must be followed in
this order, although it is possible to have other instructions between them. Any deviation from this order will cause
the CD1, CD0 bits to remain unchanged. Switching from frequency multiplier to non-multiplier mode requires no
steps other than the changing of the CD1, CD0 bits.
1) Ensure that the CD1, CD0 bits are set to 10, and the RGMD (EXIF.2) bit = 0.
2) Clear the CTM (Crystal Multiplier Enable) bit.
3) Set the 4X/2X bit to the appropriate state.
4) Set the CTM (crystal multiplier enable) bit.
5) Poll the CKRDY bit (EXIF.4), waiting until it is set to 1. This will take approximately 65,536 cycles of the
6) Set CD1, CD0 to 00. The frequency multiplier is engaged on the machine cycle following the write to these bits.
OSCILLATOR-FAIL DETECT
The microprocessor contains a safety mechanism called an on-chip oscillator-fail-detect circuit. When enabled, this
circuit causes the processor to be held in reset if the oscillator frequency falls below 40kHz. In operation, this circuit
complements the watchdog timer. Normally, the watchdog timer is initialized so that it times out and causes a
processor reset in the event that the processor loses control. In the event of a crystal or external oscillator failure,
however, the watchdog timer does not function and there is the potential for the processor to fail in an uncontrolled
state. The use of the oscillator-fail-detect circuit forces the processor to a known state (i.e., reset) even if the
oscillator stops.
The oscillator-fail-detect circuitry is enabled when software sets the enable bit OFDE (PCON.4) to 1. Please note
that software must use a timed-access procedure (described later) to write this bit. The OFDF (PCON.5) bit also
sets to 1 when the circuitry detects an oscillator failure, and the processor is forced into a reset state. This bit can
only be cleared to 0 by a power-fail reset or by software. The oscillator-fail-detect circuitry is not activated when the
oscillator is stopped due to the processor entering stop mode.
CD1
external crystal or clock source.
0
0
0
1
1
CD0
0
0
1
0
1
4X/2X
N/A
N/A
N/A
0
1
Power Management Mode
Frequency Multiplier (2X)
Frequency Multiplier (4X)
Divide-by-4 (Default)
FUNCTION
Reserved
39 of 53
MACHINE CYCLE
CLOCKS PER
1024
—
2
1
4
MAX EXTERNAL
FREQUENCY
(MHz)
20
10
40
40
—