HS2633ECH61H Renesas Technology / Hitachi Semiconductor, HS2633ECH61H Datasheet
HS2633ECH61H
Related parts for HS2633ECH61H
HS2633ECH61H Summary of contents
Page 1
... H8S/2633 Group QFP-128 User System Interface Cable Renesas Microcomputer Development Environment System Rev.5.00 2004.1.29 HS2633ECH61H User’s Manual ...
Page 2
Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may ...
Page 3
... Throughout this document, the term "user system interface cable" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products. User system interface cable (HS2633ECH61H) The user system or a host computer is not included in this definition. Purpose of the User System Interface Cable: This user system interface cable is for connecting the emulator station and user system ...
Page 4
LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface cables determined to be defective in ...
Page 5
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and ...
Page 6
READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface cable until you fully understand its mechanism. DEFINITION OF SIGNAL ...
Page 7
Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST not ...
Page 8
... Thank you for purchasing this user system interface cable (HS2633ECH61H) for the Renesas’ original microcomputer H8S/2633 group. The HS2633ECH61H is a user system interface cable that connects an H8S/2633 group E6000 emulator (HS2633EPI61H; hereinafter referred to as the emulator) to the IC socket for a QFP-128 package (package code: FP-128) for the H8S/2633 group MCU on the user system ...
Page 9
Section 1 Configuration....................................................................................1 Section 2 Connection Procedures ......................................................................4 2.1 Connecting User System Interface Cable to Emulator Station .......................................... 4 2.2 Connecting User System Interface Cable to User System................................................. 6 2.2.1 Installing IC Socket.............................................................................................. 6 2.2.2 Soldering IC Socket ............................................................................................. 7 ...
Page 10
... Section 1 Configuration Use an NQPACK128RD socket (manufactured by Tokyo Eletech Corporation) for the FP-128 package IC socket on the user system. Figure 1 shows the configuration of the HS2633ECH61H user system interface cable for the FP-128 package. CAUTION 1 ...
Page 11
... Figure 1 HS2633ECH61H User System Interface Cable 2 ...
Page 12
... Table 1 lists the HS2633ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS2633ECH61H Components No. Component 1 Cable body 2 Cable head 3 IC socket 4 Socket cover 5 Screws ( mm) 6 Screws ( mm) 7 Guide pins 8 Screwdriver 9 Documentation Quantity Remarks 1 Flat cable ...
Page 13
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will ...
Page 14
Figure 2 Connecting User System Interface Cable to Emulator Station 5 ...
Page 15
Connecting User System Interface Cable to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 ...
Page 16
Figure 3 Location Setting of IC Socket 2.2.2 Soldering IC Socket After fastening, solder the IC socket for an FP-128 package to the user system. Be sure to completely solder the leads so that the solder slops gently over the ...
Page 17
Fastening Cable Head 1. Use the screwdriber provided for tightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw ...
Page 18
Figure 4 Connecting User System Interface Cable to User System 9 ...
Page 19
Fastening Cable Body Connect the cable body to the cable head. Cable body User system 10 Remove jig Cable head Figure 5 Fastening Cable Body Removing Push the remove jig ...
Page 20
Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-128 package (NQPACK128RD: manufactured by Tokyo Eletech Corporation). Note that the ...
Page 21
Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. Figure 7 Dimensions for User System Interface Cable Head 12 ...
Page 22
Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 8. Figure 8 Resulting Dimensions after Connecting User System Interface Cable 13 ...
Page 23
Section 3 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided for tightening screws. 3. The tightening torque must be 0.054 N•m or less. If the applied torque ...
Page 24
Screws ( mm) User system Figure 9 Installing MCU to User System Socket cover MCU Pin 1 IC socket Tokyo Eletech Corporation NQPACK128RD 15 ...
Page 25
Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2633 group, turn on the emulator according to the procedures described in the H8S Family E6000 Emulator User's Manual (HS2000EPI61HE). 2. Verify the user system interface cable connections ...
Page 26
Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount ...
Page 27
... H8S/2633 Group QFP-128 User System Interface Cable HS2633ECH61H User's Manual Publication Date: Rev.5.00, January 29, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. 2004 Renesas Technology Corp. All rights reserved. Printed in Japan. ...
Page 28
... H8S/2633 Group QFP-128 User System Interface Cable HS2633ECH61H User’s Manual REJ10B0085-0500H ...