BGB101 NXP Semiconductors, BGB101 Datasheet
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
BGB101
Available stocks
Related parts for BGB101
BGB101 Summary of contents
Page 1
... DISCRETE SEMICONDUCTORS DATA SHEET BGB101 0 dBm Bluetooth radio module Preliminary specification 2003 Aug 05 ...
Page 2
... Internal shielding for better EMI (Electro Magnetic Interference) immunity. DESCRIPTION The BGB101 Bluetooth radio module is a short-range radio transceiver for wireless links operating in the globally available ISM band, between 2402 and 2480 MHz composed of a fully integrated, state-of-the-art ...
Page 3
... Autocal Channel Filter DC extractor Rx balun + filter R_DATA DCXCTR RSSI Fig.2 Block diagram. 3 Preliminary specification TOP VIEW Dimensions in mm Pin 29 represents the inner LGA pads Fig.1 Simplified outline (preliminary footprint balun + filter Band Tx/Rx pass switch filter BGB101 ANT ...
Page 4
... FUNCTIONAL DESCRIPTION Control The BGB101 Bluetooth Radio Module is controlled by a baseband processor via the serial 3-wire bus. These 3 wires are data (S_DATA), clock (S_CLK) and enable (S_EN). Data sent to the device is loaded in bursts framed by S_EN. Data and clock (S_DATA and S_CLK) signals are ignored until S_EN goes low. The programmed information is read directly into the internal registers when S_EN goes high ...
Page 5
... Due to the IF frequency at 1 MHz mode the VCO frequency should be 1 MHz higher than the channel frequency. This should be taken care of by the baseband controller. Power-down mode In Power-down mode, current consumption is reduced (typical). The 3-wire bus inputs present a high-ohmic resistance to ground. 2003 Aug 05 5 Preliminary specification BGB101 ...
Page 6
... MAIN DIVIDER FREQUENCY RATIO (MHz) 2304 + n 1.0 (2304 +n) 2402 2402 2403 2403 2480 2480 2481 2481 REFERENCE INPUT FREQUENCY 12 13 BGB101 b17 b16 see (2) (2) below 0 0 CHANNEL FREQUENCY TX channel 1 RX channel 1 TX channel 2 RX channel 78 TX channel 79 RX channel 79 12 MHz 13 MHz ...
Page 7
... Mode 1 (min/max - Medium RC - Slow RC) Mode 2 (min/max - Slow RC) Amplifier on Pre-amplifier on 7 Preliminary specification TX OUTPUT POWER (TYPICAL) 12 dBm 9 dBm 6 dBm 3 dBm 0 dBm 3 dBm 4 dBm 5 dBm DC EXTRACTION TYPE FALING EDGE DCXCTR FALING EDGE S_EN Tx/Rx switch in TX Amplifier on and Tx/Rx switch in TX BGB101 ...
Page 8
... ESD susceptibility testing. All pins withstands the following threshold voltages: PARAMETER ESD threshold voltage HBM (JESD22-A114-B) MM (JESD22-A115-A) 2003 Aug 05 CONDITIONS PARAMETER METHOD VALUE 8 Preliminary specification MIN. MAX. 0.3 3 +85 150 VALUE 30 CLASS 3500 V 300 V BGB101 UNIT dBm C C UNIT K ...
Page 9
... MHz offset; measured in 100 kHz bandwidth; referred to wanted channel; note 5 note 5 and note 6 note 5 and note 6 normalized referred to wanted output level 2450 MHz 4900 MHz; note 1; note 5 VCO 9 Preliminary specification BGB101 MIN. TYP. MAX. UNIT 2.65 2.8 3 ...
Page 10
... BER < 0.1 % wanted signal 60dBm; BER < 0.1 % wanted signal 60dBm; BER < 0.1 % wanted signal 60dBm; BER < 0.1 % wanted signal 67dBm; BER < 0.1 % wanted signal 67dBm; BER < 0 special case, see above 10 Preliminary specification BGB101 MIN. TYP. MAX. UNIT 36 dBm 30 dBm 47 dBm 47 dBm 82 75 ...
Page 11
... GHz to 12.75 GHz; note 5 measured at 2450MHz note 3 HIGH or LOW level to switch off the module: note 3 for R_DATA output for R_DATA output at 500 kHz at 500 kHz note 2 at 500 kHz at 500 kHz 11 Preliminary specification BGB101 MIN. TYP. MAX. UNIT 0 dBm 27 dBm 27 dBm 0 dBm +20 ...
Page 12
... Measured Blocking performance BGB101/BGB121, P Power level of interferer (dBm) Note that the interferer maximum power level that could be generated in the test system was limited to +19 dBm. Fig.3 Typical out-of-band blocking performance BGB101. TIMING DIAGRAMS S_DATA S_CLK S_EN 3-wire serial bus timing S_CLK/DATA REFCLK ...
Page 13
... The DCXCTR signal (in RX mode) should go low at the actual end of the trailer sequence. The timing for this transition should be directly derived from the Access Code detection algorithm inside the baseband processor. REFERENCES [1] Bluetooth test specification - RF, 20001-07-02, rev. 0.91, 20.B.353/0.91 2003 Aug 05 DESCRIPTION 13 Preliminary specification BGB101 CONDITIONS MIN. TYP. 0.1 2 0.1 note 1 ...
Page 14
... Aug 05 300 handbook, halfpage 200 100 Fig.6 Recommended reflow temperature profile. Packing An extended packing / SMD specification can be found in document SC-18 “Discrete Semiconductor Packages”. . The module is compliant with moisture sensitivity level 1. 14 Preliminary specification BGB101 MGM159 (min) ...
Page 15
... Philips Semiconductors 0 dBm Bluetooth radio module PACKAGE OUTLINE 2003 Aug Preliminary specification BGB101 ...
Page 16
... Preliminary specification BGB101 DEFINITION These products are not Philips Semiconductors ...
Page 17
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2001 All rights are reserved. Reproduction in whole or in part is prohibited ...