IGD616 CT-Concept Technologie AG, IGD616 Datasheet
IGD616
Available stocks
Related parts for IGD616
IGD616 Summary of contents
Page 1
... Its drive power and performance specifications such that now one single driver core IGD616 will cover the range of both IGD608 and IGD615 at a superior reliability level. The driver core is optimized to match various IGBTs and applications from 100A / 1200V to 1000A / 1700V and beyond. ...
Page 2
... IGD616 Preliminary Data Sheet Compatibility to IGD608 / IGD615 Gate Drivers The IGD616 is available with different options covering a dedicated set of compatible items. In this data sheet, the text referring to critical compatible items is underlined. Option N and Option I select between non-inverting and inverting inputs respectively longer possible to interchange the IN+ and IN- inputs to invert the logic. ...
Page 3
... GND 4 GND 3 GND 2 GND 1 Fig. 1 Block diagram of the IGD616 (option T, i.e. fault signal via signal transformer interface). Non-inverting inputs (option N) or inverting inputs (option I). Not connected pins are designated as N. IGD 001 Supply voltage monitoring Pulse ...
Page 4
... GND 9 DC/DC converter control GND 4 GND 3 GND 2 GND 1 Fig. 2 Block diagram of the IGD616 (option C, i.e. fault signal via optocoupler). Non-inverting inputs (option N) or inverting inputs (option I). Not connected pins are designated as N.C. Page 4 IGD 001 Supply voltage monitoring Pulse transceiver IGD616NC / IGD616IC 19 ME Vce ...
Page 5
... COM 24 COM Common terminal (secondary side ground Gate driver output 26-29 Physically not present 30-36 N.C. Not connected / reserved for future use Not connected pins are designated as N. Function IGD616 Preliminary Data Sheet Page 5 ...
Page 6
... IGD616 Preliminary Data Sheet Mechanical Data Fig. 3 Footprint of IGD616. Grid is 1.27mm (50mil). Recommended diameter of solder pad is 1.6mm. Recommended diameter of drill holes is 1.0mm. Height X = 18.5mm +/- 0.5mm for option T. Height X = 20.5mm +/- 0.5mm for option C. Page 6 CT-Concept.com ...
Page 7
... Condition/remark To GND without external Capacitors (note 9) external Capacitors < 100μF (notes 2, 9) Continuous, after startup sequence see diagram Parameter Rg: Total External Gate Resistance 1 1.5 2 2.5 3 Gate Charge [uC] To COM Continuous Soldering, 5 seconds IGD616 Preliminary Data Sheet Min. Max. Units 0 16 -16.0 +16.0 5.1 55 6.0 550 150 3.5 4 4.5 ...
Page 8
... IGD616 Preliminary Data Sheet Recommended Operating Conditions Parameter Primary supply voltage VCC Duty cycle Total external gate resistance Electrical Characteristics Unless otherwise specified, all data refer to a primary supply voltage of 15V and an ambient temperature of +25°C. Minimum and maximum values refer to the specified maximum rated operating range at ambient temperature ...
Page 9
... V(SO+) > V(SO-) Fault state Otherwise Option T: during command blocking time Option C Condition/Remark IGBT turn-on, option N IGBT turn-off, option N IGBT turn-on, option I IGBT turn-off, option I IGBT turn-on IGBT turn-off IGD616 Min. Typ. Max. Units Min. Typ. Max. Units ...
Page 10
... IGD616 Preliminary Data Sheet Electrical Insulation Operating voltage For option C; continuous (note 6) Permitted d/ C*E* Test voltage Partial discharge extinction volt. Creep path primary-secondary Creep path secondary-secondary Footnotes 1) The unipolar primary supply voltage with a nominal value of V(VCC, GND) = 15.0V is multiplied by a magnetic transformer, resulting in a unipolar secondary power supply voltage with a nominal value of V(Cs, COM ...
Page 11
... Cs and COM total of 100μF. External blocking capacitors must be applied for pulse gate charges >5.1μC. The capacitance rating must be greater or equal 2μF per 1μC gate pulse charge exceeding 5.1μC. Place the capacitors with short traces to the IGD616’s pins. Make sure to check your design for the thermal limits given in note 2. ...
Page 12
... IGD616 Preliminary Data Sheet Important Notice The data contained in this product data sheet is intended exclusively for technically trained staff. Handling all high-voltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory! Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive devices according to international standard IEC 747-1, Chapter IX or European standard EN 100015 (i ...
Page 13
... Copyright 1992…2008 by CT-Concept Technologie AG - Switzerland. We reserve the right to make any technical modifications without prior notice IGD616 Preliminary Data Sheet Type designation IGD616NC1 IGD616NT1 IGD616IC1 IGD616IT1 Upon request All rights reserved. Version from 2008-04-17 Page 13 ...