TPD4123AK TOSHIBA Semiconductor CORPORATION, TPD4123AK Datasheet
TPD4123AK
Available stocks
Related parts for TPD4123AK
TPD4123AK Summary of contents
Page 1
... The TPD4123AK brush less motor driver using high voltage PWM control fabricated by high voltage SOI process three-shunt resistor circuit for current sensing. It contains level shift high-side driver, low-side driver, IGBT outputs, FRDs and protective functions for under voltage protection circuits and thermal shutdown circuit ...
Page 2
... Pin Assignment Marking Part No. (or abbreviation code) TPD4123AK TPD4125K 2 TPD4123AK Lot Code (Weekly code) 2008-05-14 ...
Page 3
... Input Control DIAG 11 Under- Under- Under- voltage voltage voltage Protection Protection Protection High-side Level Shift Driver Thermal Shutdown Low-side Driver 3 TPD4123AK BSU 18 BSV 21 BSW IS3 IS2 20 IS1 19 GND 1/16 2008-05-14 ...
Page 4
... V-phase IGBT emitter and FRD anode pin. 21 BSV V-phase bootstrap capacitor connecting pin V-phase output pin High-voltage power supply input pin BSW W-phase bootstrap capacitor connecting pin W-phase output pin. 26 IS3 W-phase IGBT emitter and FRD anode pin. Pin Description 4 TPD4123AK 2008-05-14 ...
Page 5
... Internal circuit diagram of HU, HV, HW, LU, LV, LW input pins 2 kΩ 2 kΩ HU/HV/HW LU/LV/LW 6.5 V 6.5 V Internal circuit diagram of SD pin V REG 2 kΩ 2 kΩ SD 6.5 V 6.5 V Internal circuit diagram of DIAG pin To internal circuit kΩ To internal circuit 6 kΩ To internal circuit 6.5 V 6.5 V DIAG 5 TPD4123AK 2008-05-14 ...
Page 6
... Timing Chart Input Voltage Output voltage TPD4123AK 2008-05-14 ...
Page 7
... OFF OFF OFF OFF OFF * * * * L OFF 7 TPD4123AK High side Low side OFF OFF OFF ON OFF OFF OFF OFF ON OFF OFF OFF ON OFF ON OFF OFF ON ON OFF OFF ON OFF ON OFF OFF OFF OFF OFF ...
Page 8
... Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). (Ta = 25°C) Symbol Rating Unit V 500 OUT OUTp V -0 REG -40 to 135 °C jopr T 150 ° -55 to 150 °C stg 8 TPD4123AK 2008-05-14 ...
Page 9
... 280 off 280 dead = 280 TPD4123AK Min Typ. Max 50 280 450 13.5 15 16.5 ⎯ ⎯ 0.5 ⎯ 0.9 5 ⎯ 230 410 ⎯ 200 370 ⎯ ⎯ 2.5 ⎯ ⎯ 1.5 ⎯ ...
Page 10
... Under- Under- Under- voltage voltage voltage Protection Protection Protection Under- High-side voltage Protection Level Shift Driver Thermal Input Control Shutdown Low-side Driver 10 TPD4123AK 18 BSU 21 BSV 24 BSW IS3 26 20 IS2 ...
Page 11
... REG DIAG pin pull-up resistor SD pin pull-up resistor voltage is steady. Both of the order of the CC power supply are not cared about either. CC power supply is blocked when the TPD4123AK Remarks (Note 1) (Note 2) (Note 2) (Note 2) (Note 2) (Note 3) ⎯ line is disconnected ...
Page 12
... UVR (=11.5 V typ.)), this product is automatically CC power supply is less than 7 V, DIAG output isn't sometimes CC UVD (=9 V typ.), the high-side IGBT output shuts down off 450 ( TPD4123AK UVD (=11 V typ.), all IGBT outputs CC power supply CC UVR (=9.5 V typ.)), the BS 2008-05-14 CC ...
Page 13
... Junction temperature T 1.8 1.6 1.4 1.2 1.0 −50 150 0 Junction temperature T 8.0 I REG = 30 mA 7.5 7.0 6.5 6 (V) Control power supply voltage V 13 TPD4123AK V L – T CEsat 700 500 300 mA 50 100 150 (° – 700 500 300 mA 50 100 150 (° ...
Page 14
... Junction temperature T (° 280 0.5 A High-side Low-side 2.0 1.0 0 −50 150 0 Junction temperature T 10 UVD V BS UVR 10.0 9.5 9.0 8.5 8.0 −50 150 0 Junction temperature T 14 TPD4123AK t – T off j 50 100 150 (° – 100 150 (°C) j 2008-05-14 ...
Page 15
... Junction temperature T (°C) j 500 400 300 200 100 18 12 (V) Control power supply voltage −50 150 0 Junction temperature T 15 TPD4123AK I – (OFF =−40° =25° =135° ( – T off 700 mA ...
Page 16
... Test Circuits IGBT Saturation Voltage (U-phase low side) FRD Forward Voltage (U-phase low side) 0. TPD4123AK 15V CC 2008-05-14 ...
Page 17
... V Current Dissipation CC Regulator Voltage IM 30mA VM 17 TPD4123AK V = 15V 15V CC 2008-05-14 ...
Page 18
... Output ON/OFF Delay Time (U-phase low side 90% 10% 90 TPD4123AK 280V 560Ω 2.2μ 15V CC 10% off 2008-05-14 ...
Page 19
... BSU pin voltage from 6V to increase and change the HU pin voltage at 5 V→0 V→5 V each time. It repeats similarly output is on. When the BSU pin voltage when output is on defines the under voltage protection recovery voltage. pin voltage when output is on defines the under voltage CC 2kΩ 19 TPD4123AK U = 18V 2kΩ ...
Page 20
... V Current Dissipation (U-phase high side TPD4123AK BSU = 15V HU = 0V/ 15V CC 2008-05-14 ...
Page 21
... Turn-On/Off Loss (low side IGBT + high side FRD) Input (LU = PG) IGBT (C-E Voltage) (U-GND) Power Supply Current 5mH 2.2μ ton toff 21 TPD4123AK 280V 15V CC 2008-05-14 ...
Page 22
... Package Dimensions HDIP26-P-1332-2.00 Weight: 3.8 g (typ.) Unit : mm 22 TPD4123AK 2008-05-14 ...
Page 23
... Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 23 TPD4123AK 20070701-EN GENERAL 2008-05-14 ...