AU211 NXP Semiconductors, AU211 Datasheet - Page 4

• Manufacturer Part Number: AU211
• Description: Voltage Comparator
• Manufacturer: NXP Semiconductors

1. This rating applies for 15 V supplies. The positive input voltage limit is 30 V above the negative supply. The negative input voltage limit is
2. These specifications apply for V
3. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with 1 mA
4. The response time specified is for a 100 mV input step with 5 mV over-drive.
5. Do not short the strobe pin to ground; it should be current driven at 3 mA to 5 mA.
6. LM311B, all parameters are at V+ = 3 V 10%; V– = GND = 0 V.
Philips Semiconductors
DC ELECTRICAL CHARACTERISTICS
Over temperature range unless otherwise specified.
NOTES:
2003 Sep 30
SYMBOL
V
I
I
A
V
I
I
V
I
I
V
V
I
I
I
OS
BIAS
BAL/STR
LEAKAGE
OS
BIAS
OH
CC
EE
V
OS
SAT
OS
IN
OL
Voltage comparator
equal to the negative supply voltage or 30 V below the positive supply, whichever is less.
specifications are limited to –25 C
–55 C < T
supply up to 15 V supplies.
load. Thus, these parameters define an error band and take into account the worst case effects of voltage gain and input impedance.
Input offset voltage
Input offset current
Input bias current
Voltage gain
Response time
Saturation voltage
Strobe on current
Output leakage current
Input offset voltage
Input offset current
Input bias current
Input voltage range
Saturation voltage
Output leakage current
Positive supply current
Negative supply voltage
amb
PARAMETER
< +125 C. The offset voltage, offset current, and bias current specifications apply for any supply voltage from a single 5 V
4
6
3
3
3
3
S
6
= 15 V and 0 C < T
LM111/211 V
LM111/211 V
LM311/B V
LM311/B V
LM111/211 V
LM311/B V
T
V = 15 V (Pin 7 may
TEST CONDITIONS
V+
(V– = V
amb
I
STROBE
T
I
I
T
T
T
T
T
T
T
T
T
V
V
I
I
V
OUT
OUT
V
amb
R
amb
R
SINK
SINK
amb
amb
amb
amb
amb
amb
amb
amb
OUT
OUT
go to 5 V)
4.5 V, V– = 0 V
OUT
IN
S
S
+85 C, for the AU211 is limited to –40 C < T
GND
= 50 mA
= 50 mA
= 25 C;
= 25 C,
= 25 C
= 25 C
= 25 C
= 25 C
= 25 C
= 25 C
= 25 C
= 25 C
1, 2, 3, 6
IN
IN
50 k
= 35 V
IN
= 35 V
50 k
= 35 V
5 mV;
= 3 mA
IN
IN
8 mA
8 mA
IN
= –5 V)
–10 mV;
–10 mV;
10 mV;
–6 mV;
–5mV;
5 mV;
amb
< 70 C unless otherwise specified. With the LM211, however, all temperature
–14.5
Min
LM111/LM211
4
AU211
–14.7
0.75
13.8
0.23
Typ
200
200
0.7
4.0
3.0
0.2
0.1
5.1
4.1
60
to
Max
13.0
100
150
3.0
1.5
4.0
0.4
0.5
6.0
5.0
10
10
20
–14.5
Min
AU211/LM111/211/311/311B
amb
< +125 C, and for the LM111 is limited to
LM311
–14.7
0.75
13.8
0.23
Typ
100
200
200
2.0
6.0
3.0
0.2
5.1
4.1
to
Max
13.0
250
300
7.5
1.5
0.4
7.5
5.0
50
50
10
70
+0.5
Min
V–
LM311B
0.75
0.23
Typ
100
200
500
2.0
3.0
0.2
1.6
6
Max
–1.5
200
250
7.5
1.5
0.4
3.5
Product data
V+
25
50
10
50
V/mV
UNIT
mV
mA
mV
mA
mA
nA
nA
nA
nA
nA
ns
V
V
V
A