SCA02810-TFN-LNN Shelly, Inc., SCA02810-TFN-LNN Datasheet

Page 1

... INNOVATIVE DISPLAY TECHNOLOGIES I RVINE P: 949-417-8070/F: 949-417-8075 E-mail: Website: Part Number : Customer APPROVED BY: ( FOR CUSTOMER USE ONLY ) SOLD BY APPROVED BY 17171 M A URPHY VENUE , C 92614-5915 ALIFORNIA info@shellyinc.com www.shellyinc.com Specification SCA02810-TFN-LNN : PCB VERSION: CHECKED BY DATE: ISSUE DATE ...

Page 2

NO. 1. Cover 2. Record of Revision 3. LCD Module Physical Data 4. External Dimensions 5. Block Diagram 6. Absolute Maximum Ratings 7. Electrical Characteristics 8. Touch Screen Panel Specifications 9. Interface PIN Connections 10. Recommend Initial Code 11. Electro-Optical ...

Page 3

DATE PAGE 10/30/09 3 RECORD OF REVISION Added version # 602 (ILI9328) SUMMARY ...

Page 4

LCD MODULE PHYSICAL DATA  General Description Size Display Type Display Mode Viewing Direction Connection Type Operation temperature Storage temperature Driving IC  Mechanical Description Item Number of dots LCM dimension LCD outline Active area Dot size Dot pitch ...

Page 5

EXTERNAL DIMENSIONS ...

Page 6

BLOCK DIAGRAM RESET /CS DB0 DB15~ GND VCC VCI  Black Light Unite G2 LCD 240(RGB)*320 G320 ILI9328 G1 G139 ...

Page 7

ABSOLUTE MAXIMUM RATINGS Item Operating temperature Storage temperature Input voltage Supply voltage for logic Supply voltage for LCD NOTE the module is used above these absolute maximum ratings. It may become permanently damaged. Using the module within ...

Page 8

ELECTRICAL CHARACTERISTICS  DC Characteristics Vss= 0V, Ta= 25℃ Item Input high voltage Input low voltage Output high voltage Output low voltage Operating voltage LCD driving voltage Current consumption for LCD normal operation  Backlight unit Item Symbol Current ...

Page 9

AC Characteristics Refer to the SPEC of ILI9328 ...

Page 10

INTERFACE PIN CONNECTIONS NO. Symbol 1 DB0 2 DB1 DB2 3 DB3 4 5 GND 6 VCC 7 / IM0 LED-A 17 LED-K1 ...

Page 11

Recommend Initial Code //===================================================================================== 初始化 // //===================================================================================== void Init() { Reset(); //************* Start Initial Sequence **********// Write_Comm(0x00E3);Write_Data(0x3008); // Set internal timing Write_Comm(0x00E7);Write_Data(0x0012); // Set internal timing Write_Comm(0x00EF);Write_Data(0x1231); // Set internal timing Write_Comm(0x0001);Write_Data(0x0100); // set SS and SM bit Write_Comm(0x0002);Write_Data(0x0700); ...

Page 12

Write_Comm(0x0082);Write_Data(0x0000); Write_Comm(0x0083);Write_Data(0x0000); Write_Comm(0x0084);Write_Data(0x0000); Write_Comm(0x0085);Write_Data(0x0000); //-------------- Panel Control -------------------// Write_Comm(0x0090);Write_Data(0x0010); Write_Comm(0x0092);Write_Data(0x0600); Write_Comm(0x0007);Write_Data(0x0133); // 262K color and display ON Write_Comm(0x0022 ...

Page 13

ELECTRO-OPTICAL CHARACTERISTICS Driving condition: VDD=2.8V, I Item Light angle（°） Temp（°C） Symbol Transmissive 0 Contrast ratio 0 Brightness 0 Luminance uniformity 0 (surface within panel) Cross talk 0 Rｘ Rｙ Gｘ Gｙ Chromaticity 0 Bｘ Bｙ Wｘ Wｙ Color Reproduction ...

Page 14

Measurement conditions: Measuring Equipment Measurement Point Diameter Measurement Point Location Light source Reflectance Plate Test pattern Contrast setting Measuring procedure: Transmittance: The light source is located at the backside of the panel. 1、 Measure the light source 2、 Place the ...

Page 15

Measuring procedure: Measure the luminance Li with the points in figure 1. Figure Active Area Uniformity value (Lu): max( ) min (4).CROSS-TALK Introduction： Crosstalk is an effect where the ...

Page 16

W: The width of the rectangle in the following pictures; 5mm 2*w=10mm Pattern A ● Definitions： Cross Talk Value： CTV = |LvA - LvB| / LvA * 100% Where： LvA: Luminance measured with the centre test point of pattern A ...

Page 17

Definitions Panel color coordinates according the CIE colour system (CIE 1931). In general always requested to measure the X, Y and Z values. Here u´, v´ and L* are according CIE 1931 ...

Page 18

NTSC: =F (display)/F (NTSC’) NTSC’ primaries: Red Green Blue F (NTSC’) =74.42 12:00 9:00 6:00 Brightness x’ y’ 0.67 0.33 0.21 0.71 0.14 0.08 3:00 Brightness cure of selected segment B 2 Brightness curve of nonselected segment B 1 Driving ...

Page 19

INSPECTION CRITERION This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling method shall be in accordance with MIL-STD-105D, inspection level II and based on: Major defect: AQL ...

Page 20

Inspection standards 4.1 Major Defect Item Items to be inspected display 4.1.1 All 2) Display abnormally functional defects 3) Missing vertical，horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. 4.1.2 Missing Missing ...

Page 21

Cosmetic Defect Item Items to be inspected No Line defect L(Length) Black line, White line, Foreign 4.2.2 material under polarizer, If the Polarizer scratch can be seen after mobile phone cover assembling or in the operating condition, judge by ...

Page 22

Cosmetic Defect Item Items to be inspected No (i) Chips on corner Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. (ii)Usual surface cracks ...

Page 23

PRECAUTIONS FOR USING LCD MODULES Handing Precautions (1) The display panel is made of glass and polarizer. As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Do ...

Page 24

LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it not alter, modify or change the shape of the tab ...

Page 25

Safety ( recommended to crush damaged or unnecessary LCDs into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned. (2) If any liquid leaks out of a damaged glass cell ...