SCA05010-BFN-LNN Shelly, Inc., SCA05010-BFN-LNN Datasheet

Page 1

... INNOVATIVE DISPLAY TECHNOLOGIES I RVINE P: 949-417-8070/F: 949-417-8075 E-mail: Website: Part Number : Customer APPROVED BY: ( FOR CUSTOMER USE ONLY ) SOLD BY APPROVED BY 17171 M A URPHY VENUE , C 92614-5915 ALIFORNIA info@shellyinc.com www.shellyinc.com Specification SCA05010-BFN-LNN : Version (A001) PCB VERSION: CHECKED BY DATE: ISSUE DATE ...

Page 2

NO. 1. Cover 2. Record of Revision 3. LCD Module Physical Data 4. External Dimensions 5. Block Diagram 6. Absolute Maximum Ratings 7. Electrical Characteristics 8. Interface PIN Connections 9. Electro-Optical Characteristics 10. Inspection Criterion 11. Precautions For Using LCD ...

Page 3

DATE PAGE RECORD OF REVISION SUMMARY ...

Page 4

LCD MODULE PHYSICAL DATA  General Description Display Type Display Mode Viewing Direction Connection Type Operation temperature Storage temperature Driving IC  Mechanical Description Item Number of dots LCM dimension Active area Dot size Dot pitch Backlight 16M TFT ...

Page 5

EXTERNAL DIMENSIONS ...

Page 6

BLOCK DIAGRAM G2 G480 R0-R7 G0-G7 B0-B7 DCLK Hsync Vsync DE VDD DGND  Backlight Circuit LCD 800(RGB)*480 HX8258-A×2+HX8662-C G1 G479 ...

Page 7

A1 A2  ABSOLUTE MAXIMUM RATINGS Item Operating temperature Storage temperature Power Supply Voltage Power Supply Voltage Power Supply Voltage Input Voltage NOTE the module is used above these absolute maximum ratings. It may become permanently damaged. Using ...

Page 8

ELECTRICAL CHARACTERISTICS  DC Characteristics Item Input high voltage Input low voltage Output high voltage Output low voltage Supply voltage(1) Supply voltage(2) Supply voltage(3) Current consumption for LCD normal operation  Backlight unit Item Current CIE Brightness Luminous Uniformity ...

Page 9

INTERFACE PIN CONNECTIONS NO. Symbol 1 VLED- 2 VLED+ 3 DGND 4 VDD ...

Page 10

STANDBY 32 HSYNC 33 VSYNC DGND TIMING Timming Requirment1 (TA =25ºC, AVDD=2.75V to 3.6V, DVSS= 0V, tr=tf=2ns) Standby mode Horizontal sync input in digital parallel RGB. ...

Page 11

Timming Requirment2 Sync mode : (TA =25ºC, AVDD=2.75V to 3.6V, DVSS= 0V) Note : T +T < mode WAVEFORM ...

Page 12

...

Page 13

ELECTRO-OPTICAL CHARACTERISTICS Driving condition: VDD=3.3V, I Item Light angle（°） Temp（°C） Symbol Transmittance 0 Contrast ratio 0 Brightness 0 Luminance uniformity 0 (surface within panel) Cross talk 0 Rｘ Rｙ Gｘ Gｙ Chromaticity 0 Bｘ Bｙ Wｘ Wｙ Color Reproduction ...

Page 14

Measurement conditions: Measuring Equipment Measurement Point Diameter Measurement Point Location Light source Reflectance Plate Test pattern Contrast setting Measuring procedure: Transmittance: The light source is located at the backside of the panel. 1、 Measure the light source 2、 Place the ...

Page 15

Measuring procedure: Measure the luminance Li with the points in figure 1. Figure Active Area Uniformity value (Lu): min max( ) (4)．CROSS-TALK Introduction： Crosstalk is an effect where the ...

Page 16

Pattern (valid for all grey scales): W: The width of the rectangle in the following pictures; 5mm 2*w=10mm Pattern A ● Definitions： Cross Talk Value： CTV = |LvA - LvB| / LvA * 100% Where： LvA: Luminance measured with ...

Page 17

Definitions Panel color coordinates according the CIE color system (CIE 1931). In general always requested to measure the X, Y and Z values. Here u´, v´ and L* are according CIE 1931 ...

Page 18

Color Gamut Ratio (NTSC) related to NTSC’: NTSC: =F (display)/F (NTSC’) NTSC’ primaries: Red Green Blue F (NTSC’) =74.42 12:00 9:00 6:00 Brightness x’ y’ 0.67 0.33 0.21 0.71 0.14 0.08 3:00 Brightness cure of selected segment B 2 Brightness ...

Page 19

INSPECTION CRITERION This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling method shall be in accordance with MIL-STD-105D, inspection level II and based on: Major defect: AQL ...

Page 20

Inspection standards 4.1 Major Defect Item Items to be inspected display 4.1.1 All 2) Display abnormally functional defects 3) Missing vertical，horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. 4.1.2 Missing Missing ...

Page 21

Cosmetic Defect Item Items to be inspected No Line defect L(Length) Black line, White line, Foreign 4.2.2 material under polarizer, If the Polarizer scratch can be seen after mobile phone cover assembling or in the operating condition, judge by ...

Page 22

Cosmetic Defect Item Items to be inspected No (i) Chips on corner Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. (ii)Usual surface cracks ...

Page 23

PRECAUTIONS FOR USING LCD MODULES Handing Precautions (1) The display panel is made of glass and polarizer. As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Do ...

Page 24

LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it not alter, modify or change the shape of the tab ...

Page 25

Precautions for Operation (1) Viewing angle varies with the change of liquid crystal driving voltage (VLCD). Adjust VLCD to show the best contrast. ( indispensable condition to drive LCD's within the specified voltage limit since the higher ...