AD7416 Analog Devices, Inc., AD7416 Datasheet - Page 10

• Manufacturer Part Number: AD7416
• Description: 10-bit Digital Temperature Sensor Ad7416 And Single/four-channel Adc Ad7417/ad7418
• Manufacturer: Analog Devices, Inc.

AD7416/AD7417/AD7418
Figure 5 shows the method the AD7416/AD7417/AD7418 uses
to measure the device temperature. To measure V
sor (substrate transistor) is switched between operating currents
of I and N × I. The resulting waveform is passed through a
chopper-stabilized amplifier that performs the functions of
amplification and rectification of the waveform to produce a dc
voltage proportional to V
This voltage is measured by the ADC to give a temperature
output in 10-bit twos complement form.
The temperature resolution of the ADC is 0.25°C, which corre-
sponds to 1 LSB of the ADC. The ADC can theoretically measure
a temperature span of 255°C; the guaranteed temperature range
is –40°C to +125°C. The result of the conversion is stored in
the Temperature Value Register (00h) as a 16-bit word. The
10 MSBs of this word store the temperature measurement (see
Table III and Table IV).
The temperature conversion formula using the 10 MSBs of the
Temperature Value Register is
INTERNAL REGISTER STRUCTURE
The AD7417/AD7418 has seven internal registers, as shown in
Figure 6. Six of these are data registers and one is an Address
Pointer Register. The AD7416 has five internal registers (the
ADC and Config2 Registers are not applicable to the AD7416).
(SELECTS DATA REGISTER
1. Positive Temperature = ADC Code/4
2. Negative Temperature = (ADC Code* – 512)/4
*MSB is removed from the ADC Code.
ADDRESS POINTER
FOR READ/WRITE)
Figure 6. AD7417/AD7418 Register Structure
REGISTER
ADDRESS
INTERFACE
BE
SERIAL
BUS
.
CONFIGURATION
T
TEMPERATURE
ADDRESS 00h)
ADDRESS 01h)
ADDRESS 02h)
T
ADDRESS 03h)
ADDRESS 04h)
ADDRESS 05h)
HYST
(READ/WRITE
(READ/WRITE
(READ/WRITE
(READ/WRITE
(READ-ONLY
(READ-ONLY
OTI
REGISTER
REGISTER
REGISTER
REGISTER
REGISTER
REGISTER
CONFIG2
VALUE
SETPOINT
SETPOINT
ADC
DATA
BE
, the sen-
SDA
SCL
–10–
ADDRESS POINTER REGISTER
The Address Pointer Register is an 8-bit register that stores an
address that points to one of the six data registers. The first data
byte of every serial write operation to the AD7416/AD7417/
AD7418 is the address of one of the data registers, which is
stored in the Address Pointer Register, and selects the data
register to which subsequent data bytes are written. Only the
three LSBs of this register are used to select a data register.
P7*
0
*P3 to P7 must be set to 0.
P2
0
0
0
0
1
1
TEMPERATURE VALUE REGISTER (ADDRESS 00h)
The Temperature Value Register is a 16-bit, read-only register
whose 10 MSBs store the temperature reading from the ADC in
10-bit twos complement format. Bits 5 to 0 are unused.
D15 D14 D13 D12 D11 D10 D9
MSB B8
The temperature data format is shown in Table IV. This shows
the full theoretical range of the ADC from –128°C to +127°C,
but in practice, the temperature measurement range is limited
to the operating temperature range of the device.
P6*
0
P1
0
0
1
1
0
0
Temperature
–128°C
–125°C
–100°C
–75°C
–50°C
–25°C
–0.25°C
0°C
+0.25°C
+10°C
+25°C
+50°C
+75°C
+100°C
+125°C
+127°C
Table III. Temperature Value Register
Table IV. Temperature Data Format
B7
Table I. Address Pointer Register
P5*
0
Table II. Register Addresses
P0
0
1
0
1
0
1
B6
P4*
0
B5
Registers
Temperature Value (Read-Only)
Config Register (Read/Write)
T
T
ADC (AD7417/AD7418 Only)
Config2 (AD7417/AD7418 Only)
HYST
OTI
B4
P3*
0
Digital Output
10 0000 0000
10 0000 1100
10 0111 0000
10 1101 0100
11 0011 1000
11 1001 1100
11 1111 1111
00 0000 0000
00 0000 0001
00 0010 1000
00 0110 0100
00 1100 1000
01 0010 1100
01 1001 0000
01 1111 0100
01 1111 1100
(Read/Write)
B3
P2
Register Select
D8
B2
P1
D7
B1
REV. G
P0
D6
LSB