AD7416 Analog Devices, Inc., AD7416 Datasheet - Page 15
![no-image](/images/no-image-200.jpg)
AD7416
Manufacturer Part Number
AD7416
Description
10-bit Digital Temperature Sensor Ad7416 And Single/four-channel Adc Ad7417/ad7418
Manufacturer
Analog Devices, Inc.
Datasheet
1.AD7416.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD7416AR
Manufacturer:
AD
Quantity:
5 510
Company:
Part Number:
AD7416AR
Manufacturer:
AD
Quantity:
10 183
Part Number:
AD7416AR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7416AR-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7416ARM
Manufacturer:
AD
Quantity:
13 888
Part Number:
AD7416ARM
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7416ARM-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7416ARMZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
With a V
40 µs (or 10% of the time) in conversion mode. It spends 360 µs
(or 90% of time) in partial power-down mode. Thus, the aver-
age power dissipated by the AD7416/AD7417/AD7418 is
Mode 2
For applications where temperature measurements are required at
a slower rate, e.g., every second, power consumption of the part
can be reduced by writing to the part to go to a full power-down
between reads. The current consumption in full power-down is
typically 0.2 µA and full power-down is initiated when D0 = 1
in the Configuration Register. When a measurement is required,
a write operation can be performed to power-up the part. The
part then performs a conversion and is returned to power-down.
The temperature value can be read in the full power-down
because the I
The power dissipation in this mode depends on the rate at which
reads take place. Taking the requirements for a temperature
measurement every 100 ms as an example, the optimum power
dissipation is achieved by placing the part in full power-down,
waking it up every 100 ms, letting it operate for 400 µs and
putting it into full power-down again. In this case, the average
power consumption is calculated as follows. The part spends
40 µs (or 0.04% of time) converting with 3 mW dissipation and
a 99.96 ms (99.96% of time) in full shutdown with 60 nW dissipa-
tion. Thus, the average power dissipation is
The fastest throughput rate at which the AD7416/AD7417/
AD7418 can be operated is 2.5 kHz (i.e., a read every 400 µs
conversion period). Since T
read time with the I
If temperature reads are called too often, reads will overlap
with conversions, aborting them continuously, which results in
invalid readings.
CONVERT START MODE
The AD7417/AD7418 has an extra mode, set by writing to the
MSB of the Config2 Register.
CONVST Pin Mode
By setting the CONVST Mode Bit to 1, conversions are initiated
only by using the CONVST pin. In this method of operation,
CONVST is normally low.
The rising edge of CONVST starts the power-up time. This
power-up time is 4 µs. If the CONVST high time is longer than
4 µs, a conversion is initiated on the falling edge of CONVST
and the track-and-hold also enters its hold mode at this time. If
the CONVST high time is less than 4 µs, an internal timer,
initiated by the rising edge of CONVST holds off the track-and-
hold and the initiation of conversion until the timer times out
(4 µs after the rising edge of CONVST, which corresponds with
the power-up time). CONVST input remains low at the end of
conversion, thus causing the part to enter its power-down mode.
In this method of operation, CONVST is normally low with a
high going pulse controlling the power-up and conversion starts.
REV. G
DD
3
mW
= 3 V, for each 400 µs cycle, the AD7416 spends
2
3
C bus is continuously active.
mW ×
×
0 004 60
2
.
C operating at 100 kbit/s would be 270 µs.
0 1 1
.
+
+
OTI
mW
nW
and T
×
×
0 9 1 2
0 9996 1 2
HYST
.
.
=
are 2-byte reads, the
.
=
mW
. µ
W
–15–
The CONVST pin should not be pulsed when reading from or
writing to the port.
Figure 17 shows the recommended minimum times for the
CONVST pulse when the temperature channel is selected.
Figure 18 shows the minimum times an analog input channel
is selected.
APPLICATIONS INFORMATION
SUPPLY DECOUPLING
The AD7416/AD7417/AD7418 should be decoupled with a
0.1 µF ceramic capacitor between V
particularly important if the part is mounted remote from the
power supply.
POWER-ON-RESET
To ensure proper power-on-reset, make sure that the supply
voltage on the V
AN-588 for more information. A failed power-on-reset can
prevent the default values from being loaded into the AD7416/
AD7417/AD7418 registers. If the correct values are not loaded
into the registers, then the device will not start operating. The
output from the value registers will be a constant value.
To get the device operating again, the registers will have to be
loaded with their default values via the I
the event of an inadequate power-on-reset and for all three
devices, the following registers should be loaded with their
default values:
MOUNTING THE AD7416
The AD7416/AD7417/AD7418 can be used for surface or air
temperature sensing applications. If the device is cemented to a
surface with thermally conductive adhesive, the die temperature
will be within about 0.2°C of the surface temperature, thanks to
the device’s low power consumption. Care should be taken to
insulate the back and leads of the device from the air, if the
ambient air temperature is different from the surface tempera-
ture being measured.
The ground pin provides the best thermal path to the die, so the
temperature of the die will be close to that of the printed circuit
ground track. Care should be taken to ensure that this is in good
thermal contact with the surface being measured.
As with any IC, the AD7416/AD7417/AD7418 and its associ-
ated wiring and circuits must be kept free from moisture to
prevent leakage and corrosion, particularly in cold conditions
where condensation is more likely to occur. Water resistant
varnishes and conformal coatings can be used for protection.
The small size of the AD7416 package allows it to be mounted
inside sealed metal probes that provide a safe environment for
the device.
Configuration Register 1—Default Value = 00h
Configuration Register 2—Default Value = 00h
T
T
HYST
OTI
Setpoint Register—Default Value = 5500h
Setpoint Register—Default Value = 4B00h
DD
pin is at 0 V. Refer to application note
AD7416/AD7417/AD7418
DD
2
and GND. This is
C bus. Therefore, in