ATA8741 ATMEL Corporation, ATA8741 Datasheet - Page 143
ATA8741
Manufacturer Part Number
ATA8741
Description
Manufacturer
ATMEL Corporation
Datasheet
1.ATA8741.pdf
(238 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATA8741-PXQW
Manufacturer:
ATMEL
Quantity:
6 000
- Current page: 143 of 238
- Download datasheet (4Mb)
23.3.4
9140B–INDCO–07/09
Two-wire Mode
The USI Two-wire mode is compliant to the Inter IC (TWI) bus protocol, but without slew rate lim-
iting on outputs and input noise filtering. Pin names used by this mode are SCL and SDA.
Figure 23-4. Two-wire Mode Operation, Simplified Diagram
Figure 23-4 on page 143
one as Slave. It is only the physical layer that is shown since the system operation is highly
dependent of the communication scheme used. The main differences between the Master and
Slave operation at this level, is the serial clock generation which is always done by the Master,
and only the Slave uses the clock control unit. Clock generation must be implemented in soft-
ware, but the shift operation is done automatically by both devices. Note that only clocking on
negative edge for shifting data is of practical use in this mode. The slave can insert wait states at
start or end of transfer by forcing the SCL clock low. This means that the Master must always
check if the SCL line was actually released after it has generated a positive edge.
Since the clock also increments the counter, a counter overflow can be used to indicate that the
transfer is completed. The clock is generated by the master by toggling the USCK pin via the
PORT Register.
The data direction is not given by the physical layer. A protocol, like the one used by the
TWI-bus, must be implemented to control the data flow.
SLAVE
MASTER
Bit7
Bit7
Bit6
Bit6
Bit5
Bit5
shows two USI units operating in Two-wire mode, one as Master and
Bit4
Bit4
Bit3
Bit3
Bit2
Bit2
Bit1
Bit1
Bit0
Bit0
Two-wire Clock
Control Unit
PORTxn
HOLD
SCL
SDA
SCL
SDA
SCL
ATA8741
VCC
143
Related parts for ATA8741
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Digital Attenuator, 50 Db, 6-bit, Ttl Driver, Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Voltage Variable Absorptive Attenuator, 30 Db 0.5 - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
3 Volt Voltage Variable Absorptive Attenuator 40 Db, 0.5-2.0 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenu A T O R, 15 Db, 4-bit Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenuator, 30 Db, 4-bit Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenuator, 28 Db, 3-bit Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenuator, 15.5 Db, 5-bit Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
2.25 Volt Voltage Variable Absorptive Attenuator - 40 dB/ 1.8.2.5 GHz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Low Current/ High Performance NPN Silicon Bipolar Transistor
Manufacturer:
Agilent(Hewlett-Packard)
Datasheet:
Part Number:
Description:
Low Current/ High Performance NPN Silicon Bipolar Transistor
Manufacturer:
Agilent(Hewlett-Packard)
Datasheet:
Part Number:
Description:
Low Current/ High Performance NPN Silicon Bipolar Transistor
Manufacturer:
Agilent(Hewlett-Packard)
Datasheet:
Part Number:
Description:
(AT-332 / AT-337) Voltage Variable Absorptive Attenuator DC - 2 GHz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenuator, 31.5 Db, 6-bit, Ttl Driver, Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
2.25 Volt Voltage Variable Absorptive Attenuator - 40 Db, 1.8.2.5 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenuator, 30 Db, 4-bit, Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet: