MT8931C Zarlink Semiconductor, MT8931C Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_sml.jpg)
MT8931C
Manufacturer Part Number
MT8931C
Description
4 Wire Full-duplex 2B+D (192 Kbps) Data Format Isdn S And T Subscriber Network Interface Circuit
Manufacturer
Zarlink Semiconductor
Datasheet
1.MT8931C.pdf
(39 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MT8931CE
Manufacturer:
MITEL
Quantity:
20 000
Part Number:
MT8931CP
Manufacturer:
MITEL
Quantity:
20 000
filtering out jitter which may be present on the
received line port.
The SNIC uses the first four channels on the
ST-BUS (as shown in Figure 4).
distribution of
provides a delayed frame pulse (F0od) to eliminate
the need for a channel
signal is used to drive subsequent devices in the
daisy chain (refer Figure 13).
arrangement, only the first SNIC in the chain will
receive the system frame pulse (F0b) with the
following devices receiving its predecessor’s delayed
output frame pulse (F0od).
The SNIC makes efficient use of its TDM bus
through the Star configuration. It does so by sharing
four common ST-BUS channels to multiple NT
devices.
physically independent S-Busses can be connected
in parallel to realize a star configuration (as shown in
Figure 14). All devices connected into the star will
carry the same input, thus information is sent to all
TEs simultaneously. The 2B+D data received from
every TE is transmitted to all NTs through the STAR
pin. Consequently, all the DSTo streams will carry
identical 2B+D data reflecting what is being
transmitted by the various TEs.
12
A
S
Y
N
C
S
Y
N
C
A4
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
Address Lines
Up to eight SNICs in NT mode with
A3
0
0
0
0
0
0
0
0
1
1
0
0
1
1
1
1
1
1
1
1
the
A2
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
serial
A1
0
0
1
1
0
0
1
1
0
0
0
1
0
0
1
1
0
0
1
1
assignment circuit. This
A0
0
1
0
1
0
1
0
1
0
1
0
0
0
1
0
1
0
1
0
1
stream,
In this type of
HDLC Address Byte #1 Register
HDLC Address Byte #2 Register
To simplify the
HDLC Interrupt Mask Register
C-channel Control Register
ST-BUS Control Register
HDLC Control Register 1
HDLC Control Register 2
Table 2. SNIC Address Map
Master Control Register
the
S-Bus Tx B1-channel
S-Bus Tx B2-channel
S-Bus Tx D-channel
Control Register 1
DSTo B1-channel
DSTo B2-channel
DSTo C-channel
DSTo D-channel
HDLC Tx FIFO
Not Available
SNIC
Write
The flow of data in the direction of S-Bus to ST-BUS
is transparent to the SNIC, regardless of the state
machine status. On the other hand, the flow of data
in the direction of ST-BUS to S-Bus becomes
transparent only after the state machine is in the
active state (IS0, IS1=1,1), in case of an NT, or in the
synchronization state (IS0, IS1=1), in case of a TE.
Microprocessor/Control Interface
The microprocessor port is compatible with either
Motorola or Intel multiplexed bus signals and timing.
The MOTEL
Compatible bus) uses the level of the DS/RD pin
at the rising edge
appropriate
rising edge of AS/ALE (refer to Figure 26) then
Motorola bus timing is selected. Conversely, if DS/
RD is high at the rising edge of AS/ALE (refer to
Figures 24 & 25), then Intel bus timing is selected.
This has the effect of redefining the microprocessor
port transparently to the user.
The user has the option of writing to the C-channel
Control or Diagnostic Register through the parallel
port interface or through the C-channel on DSTi. Bit
0 of the Master Control Register provides this option.
bus timing.
circuit
HDLC Interrupt Status Register
C-channel Status Register
of
Master Status Register
HDLC Status Register
S-Bus Rx B1-channel
S-Bus Rx B2-channel
S-Bus Rx D-channel
DSTi B1-channel
DSTi B2-channel
DSTi C-channel
DSTi D-channel
(MOtorola
HDLC Rx FIFO
AS/ALE
Not Available
If DS/RD is low at the
Read
verify
verify
verify
verify
verify
to
Data Sheet
and
select
InTEL
the