ISL5585 Intersil Corporation, ISL5585 Datasheet - Page 3

• Manufacturer Part Number: ISL5585
• Description: 3.3 Volt Ringing Slic Family For Voice Over Broadband (VOB)
• Manufacturer: Intersil Corporation

Pin Description
PLCC
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
---
28
1
2
3
4
5
6
7
8
9
QFN
29
30
31
32
10
11
12
13
14
15
17
18
19
20
21
22
23
24
25
26
27
1
2
3
4
5
6
7
9
SYMBOL
BGND
AGND
BSEL
RING
SWC
SW+
CDC
SCC
VBH
DET
ALM
POL
VRS
AUX
VCC
VBL
SW-
VTX
VFB
ILIM
TIP
-IN
RT
SH
E0
F2
F1
F0
TL
TIP power amplifier output.
Battery Ground - To be connected to zero potential. All loop current and longitudinal current flow from this
ground. Internally separate from AGND. This ground must be connected to the same potential as AGND.
Low battery supply connection.
High battery supply connection for the most negative battery.
Uncommitted switch positive terminal.
Uncommitted switch negative terminal.
Switch control input. This TTL compatible input controls the uncommitted switch, with a logic “0” enabling
the switch and logic “1” disabling the switch.
Mode Control Input - MSB. F2-F0 for the TTL compatible parallel control interface for controlling the
various modes of operation of the device.
Mode control input.
Mode control input.
Detector Output Selection Input. This TTL input controls the multiplexing of the SHD (E0 = 1) and GKD
(E0 = 0) comparator outputs to the DET output based upon the state at the F2-F0 pins (see the Device
Operating Modes table shown on page 2).
Detector Output - This TTL output provides on-hook/off-hook status of the loop based upon the selected
operating mode. The detected output will either be switch hook, ground key or ring trip (see the Device
Operating Modes table shown on page 2). DET will be latched low following a ring trip. Unlatching the
DET pin is accomplished by changing logic state.
Thermal Shutdown Alarm. This pin signals the internal die temperature has exceeded safe operating
temperature (approximately 175
Analog ground reference. This pin should be externally connected to BGND.
Selects between high and low battery, with a logic “1” selecting the high battery and logic “0” the low
battery.
Programming pin for the transient current limit feature, set by an external resistor to ground.
External capacitor on this pin sets the polarity reversal time.
Ringing Signal Input - Analog input for driving 2-wire interface while in Ring Mode.
Auxiliary input - Float if not used.
Transmit Output Voltage - Output of impedance matching amplifier, AC couples through a resistor to
CODEC.
Feedback voltage for impedance matching. This voltage is scaled to accomplish impedance matching.
The CFB capacitor connects between this pin and the -IN pin. The CFB cap needs to be non-polarized
for proper device operation in the Reverse Active mode. Ceramic surface mount capacitors (1206 body
style) are available from Panasonic with a 6.3V voltage rating. These can be used for CFB since it is
internally limited to approximately ±3V.
Analog Receive Voltage - 4-wire analog audio input voltage. connects to CODEC via receive gain setting
resistor R
parasitic capacitance.
Positive voltage power supply,+3.3V
DC Biasing Filter Capacitor - Connects between this pin and V
polarized or non polarized with a 6.3V voltage rating.
Ring trip filter network.
Loop Current Limit programming resistor.
Switch hook detection threshold programming resistor.
Substrate Common Connection - Connect this pin to VBH Supply. This pin is used to connect the
substrate of the die and the thermal heatsink plane of the QFN package.
RING power amplifier output.
3
IN
(see Figure 18). Resistor R
o
C) and the device has been powered down automatically.
ISL5585
IN
needs to be as close to the -IN pin as possible to minimize
DESCRIPTION
CC
.The CDC capacitor may be either