PIC16CR58A Microchip Technology, PIC16CR58A Datasheet - Page 232

• Manufacturer Part Number: PIC16CR58A
• Description: ROM-Based 8-Bit CMOS Microcontroller Series
• Manufacturer: Microchip Technology

PIC16C6X
21.1
DS30234D-page 232
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
DC CHARACTERISTICS
D001
D001A
D002*
D003
D004*
D005
D010
D013
D015*
D020
D021
D021A
D021B
D023*
Note 1: This is the limit to which V
Param
No.
*
†
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from character-
6: The
These parameters are characterized but not tested.
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and
are not tested.
DC Characteristics:
Supply Voltage
RAM Data Retention
Voltage (Note 1)
V
ensure internal Power-on
Reset signal
V
internal Power-on Reset
signal
Brown-out Reset Voltage
Supply Current (Note 2, 5)
Brown-out Reset Current
(Note 6)
Power-down Current
(Note 3, 5)
Brown-out Reset Current
(Note 6)
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all I
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to V
MCLR = V
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
mated by the formula Ir = V
ization and is for design guidance only. This is not tested.
added to the base I
DD
DD
start voltage to
rise rate to ensure
Characteristic
current is the additional current consumed when this peripheral is enabled. This current should be
DD
; WDT enabled/disabled as specified.
DD
or I
PD
DD
DD
PIC16C63/65A-04 (Commercial, Industrial, Extended)
PIC16C63/65A-10 (Commercial, Industrial, Extended)
PIC16C63/65A-20 (Commercial, Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
DD
V
V
S
I
I
V
B
DD
PD
Sym
measurement.
I
I
can be lowered without losing RAM data.
DD
DR
POR
VDD
VDD
measurements in active operation mode are:
BOR
BOR
/2Rext (mA) with Rext in kOhm.
0.05
Min
4.0
4.5
3.7
3.7
-
-
-
-
-
-
-
-
-
-
Typ† Max Units
10.5
V
350
350
1.5
4.0
4.0
2.7
1.5
1.5
2.5
10
-
-
SS
-
425
425
6.0
5.5
4.3
4.4
20
42
16
19
19
5
-
-
-
-40˚C
0˚C
-40˚C
V/ms See section on Power-on Reset for details
mA
mA
V
V
V
V
V
V
A
A
A
A
A
A
T
T
T
XT, RC and LP osc configuration
HS osc configuration
See section on Power-on Reset for details
BODEN configuration bit is enabled
Extended Range Only
XT, RC, osc config F
V
HS osc config F
BOR enabled, V
V
V
V
V
BOR enabled, V
A
A
A
DD
DD
DD
DD
DD
= 5.5V (Note 4)
= 4.0V, WDT enabled,-40 C to +85 C
= 4.0V, WDT disabled,-0 C to +70 C
= 4.0V, WDT disabled,-40 C to +85 C
= 4.0V, WDT disabled,-40 C to +125 C
+125˚C for extended,
+85˚C for industrial and
+70˚C for commercial
DD
OSC
DD
DD
1997 Microchip Technology Inc.
,
Conditions
= 5.0V
= 5.0V
= 20 MHz, V
OSC
DD
= 4 MHz,
and V
SS
DD
.
= 5.5V