ISL54402 Intersil Corporation, ISL54402 Datasheet
ISL54402
Available stocks
Related parts for ISL54402
ISL54402 Summary of contents
Page 1
... THD+N at 12mW into 32Ω Load . . . . . . . . . . . <0.007% • Cross-talk (20Hz to 20kHz -110dB • 1.8V Logic Compatible (ISL54402) • Single Supply Operation (V - ISL54400 and ISL54401 . . . . . . . . . . . . . . 2.5V to 3.6V - ISL54402 . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8V to 5.5V • Available in Ultra-thin • Pb-Free Plus Anneal Available (RoHS Compliant) Applications • MP3 and other Personal Media Players • ...
Page 2
... TOP VIEW IN1 NO1 IN2 8 NO2 COM1 NC1 7 50kΩ COM2 6 NC2 50kΩ not present (or idle). ISL54402 Switches Shown for Logic “0” Inputs. BUS V TERM 10 5.3kΩ POWER/LOGIC CONTROL D+ 8 2MΩ 50kΩ 50kΩ ...
Page 3
... D+ USB Differential Input 9 D- USB Differential Input 10 V USB V Voltage, Outputs TERM TERM 3.3V to 4.0V when V BUS to 5.25V and V = logic “1” and DD connected to Upstream USB Termination. 3 ISL54400, ISL54401, ISL54402 D+, D- OFF ON + 0. TERM OFF Open ON Open OFF Open ON 3.3V to 4.0V + 0.8V DD NOx ...
Page 4
... NiPdAu termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 4 ISL54400, ISL54401, ISL54402 TEMP. RANGE (°C) - ...
Page 5
... ∆R (ISL54400 and ISL54401 V = Voltage at max Only) 5 ISL54400, ISL54401, ISL54402 Thermal Information Thermal Resistance (Typical, Note 3x3 TDFN Package . . . . . . . . . . . . . . . . . . . . 10 Ld µQFN Package . . . . . . . . . . . . . . . . . . . . . . . ) + 0.3V) Maximum Junction Temperature (Plastic Package 150° 0.3V) Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C BUS ) + 0 ...
Page 6
... V LOFF ROFF NCxOFF NC COM ON Capacitance 1MHz, V D-/L(ON D+/R(ON) COMx(ON ISL54400, ISL54401, ISL54402 Test Conditions 1.4V 0.5V (Notes 4, 6), Unless Otherwise Specified (Continued) INH INL TEST CONDITIONS = 4.4V 40mA BUS COM D+ , (Note 7) = 1.4V 40mA INx ...
Page 7
... value, between L and R, between NC1 and NC2 or between D+ and D-, or between NO1 and NO2 ISL54400, ISL54401, ISL54402 Test Conditions +3.0V, GND = 0V 1.4V 0.5V (Notes 4, 6), Unless Otherwise Specified (Continued) ...
Page 8
... Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1A. MEASUREMENT POINTS V INH LOGIC INPUT V INL SWITCH OUTPUT V OUT 0V FIGURE 2A. MEASUREMENT POINTS FIGURE 2. BREAK-BEFORE-MAKE TIME (ISL54402 ONLY /40mA 40mA V 1 COM GND Repeat test for all switches. Note: COM designation in diagram refers to: D-/L, D+/R, COM1, and COM2 ...
Page 9
... OUT+ t skew_o OUT- 50% 90% 10 FIGURE 7A. MEASUREMENT POINTS 9 ISL54400, ISL54401, ISL54402 (Continued OUT + BUS IN OUT - FIGURE 6. RISE/FALL TIME MISMATCH TEST DIN+ DIN- |tro - tri| Delay Due to Switch for Rising Input and Rising Output Signals. ...
Page 10
... For the ISL54402 part the NC1 audio switch is active (turned ON) whenever logic pin IN1 (pin 10) is LOW. The NC2 audio switch is active (turned ON) whenever the logic pin IN2 (pin 2) is LOW ...
Page 11
... SPDT switches work in tandem, the ISL54402 gives you independent control over each SPDT switch. USB Switches The two NO (normally open) USB switches (D+, D-, NOx) are 5Ω bidirectional switches that are designed to pass low speed and full-speed USB differential signals typically in the range ...
Page 12
... ISL54402 Operation The ISL54402 is an audio/data switch. Its logic control is typical of a standard dual SPDT switch. The digital control for the ISL54402 are the IN pins (pin 2 and pin 10). These pins are 1.8V logic compatible when operated with a 3.0V supply. The device has been designed ...
Page 13
... Typical Performance Curves MASK: FS (12Mbps) 13 ISL54400, ISL54401, ISL54402 T = 25°C, Unless Otherwise Specified (Continued) A TIME (10ns/DIV) FIGURE 11. EYE PATTERN: 12Mbps FN6240.3 July 12, 2006 ...
Page 14
... X e BOTTOM VIEW C L (A1 SECTION "C-C" FOR ODD TERMINAL/SIDE b 0.05 MIN 0.10 MIN DETAIL “A” PIN ISL54400, ISL54401, ISL54402 L10.2.1x1. LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE E SYMBOL 4xk Ne (DATUM B) NOTES ...
Page 15
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 15 ISL54400, ISL54401, ISL54402 L10.3x3A 0.10 C ...