ISL83202 Intersil Corporation, ISL83202 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
ISL83202
Manufacturer Part Number
ISL83202
Description
1A Peak Current H-Bridge FET Driver
Manufacturer
Intersil Corporation
Datasheet
1.ISL83202.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL83202IBZ
Manufacturer:
Intersil
Quantity:
288
Company:
Part Number:
ISL83202IBZ
Manufacturer:
Intersil
Quantity:
322
Part Number:
ISL83202IBZ
Manufacturer:
INTERSIL
Quantity:
20 000
Pin Descriptions
NUMBE
PIN
10
12
13
14
15
16
11
R
1
2
3
4
5
6
7
8
9
SYMBOL
AHO
BHO
BHB
AHB
AHS
ALO
BLO
BHS
DEL
V
V
BHI
AHI
DIS
BLI
ALI
SS
DD
B High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap diode
and positive side of bootstrap capacitor to this pin.
B High-side Input. Logic level input that controls BHO driver (Pin 16). BLI (Pin 3) high level input overrides BHI high level
input to prevent half-bridge shoot-through, see Truth Table. DIS (Pin 8) high level input overrides BHI high level input. The
pin can be driven by signal levels of 0V to 15V (no greater than V
B Low-side Input. Logic level input that controls BLO driver (Pin 14). If BHI (Pin 2) is driven high or not connected externally
then BLI controls both BLO and BHO drivers, with dead time set by delay currents at DEL (Pin 5). DIS (Pin 8) high level
input overrides BLI high level input. The pin can be driven by signal levels of 0V to 15V (no greater than V
A Low-side Input. Logic level input that controls ALO driver (Pin 13). If AHI (Pin 7) is driven high or not connected externally
then ALI controls both ALO and AHO drivers, with dead time set by delay currents at DEL (Pin 5). DIS (Pin 8) high level
input overrides ALI high level input. The pin can be driven by signal levels of 0V to 15V (no greater than V
Turn-on DELay. Connect resistor from this pin to V
drivers turn-off with no adjustable delay, so the DEL resistor guarantees no shoot-through by delaying the turn-on of all
drivers. The voltage across the DEL resistor is approximately V
Chip negative supply, generally will be ground.
A High-side Input. Logic level input that controls AHO driver (Pin 10). ALI (Pin 4) high level input overrides AHI high level
input to prevent half-bridge shoot-through, see Truth Table. DIS (Pin 8) high level input overrides AHI high level input. The
pin can be driven by signal levels of 0V to 15V (no greater than V
DISable input. Logic level input that when taken high sets all four outputs low. DIS high overrides all other inputs. When
DIS is taken low the outputs are controlled by the other inputs. The pin can be driven by signal levels of 0V to 15V (no
greater than V
A High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap diode
and positive side of bootstrap capacitor to this pin.
A High-side Output. Connect to gate of A High-side power MOSFET.
A High-side Source connection. Connect to source of A High-side power MOSFET. Connect negative side of bootstrap
capacitor to this pin.
Positive supply to control logic and lower gate drivers. De-couple this pin to V
A Low-side Output. Connect to gate of A Low-side power MOSFET.
B Low-side Output. Connect to gate of B Low-side power MOSFET.
B High-side Source connection. Connect to source of B High-side power MOSFET. Connect negative side of bootstrap
capacitor to this pin.
B High-side Output. Connect to gate of B High-side power MOSFET.
6
DD
).
ISL83202
ISL83202
SS
DESCRIPTION
to set timing current that defines the dead time between drivers. All
DD
DD
DD
-2V.
).
).
SS
(Pin 6).
DD
DD
December 20, 2006
).
).
FN6382.0