TC1054 TelCom Semiconductor, TC1054 Datasheet - Page 4
TC1054
Manufacturer Part Number
TC1054
Description
50mA CMOS LDO WITH SHUTDOWN AND ERROR OUTPUT
Manufacturer
TelCom Semiconductor
Datasheet
1.TC1054.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TC1054-1.8VCT713
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
TC1054-2.5VCT713
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
TC1054-2.6VCT713
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
TC1054-2.7VCT713
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
TC1054-2.85VCT713
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
TC1054-3.0VCT713
Manufacturer:
MICROCHIP
Quantity:
12 000
PRELIMINARY INFORMATION
TC1054
TC1054-01 6/12/97
DETAILED DESCRIPTION
tor. (If an adjustable version is desired, please see the
TC1070 or TC1071 data sheets.) Unlike the bipolar regula-
tors, the TC1054 supply current does not increase with load
current. In addition, V
tion at very low load currents (an important consideration in
RTC and CMOS RAM battery back-up applications).
tor is enabled any time the shutdown input (SHDN) is at or
above V
below V
or I/O port of a microcontroller. If the SHDN input is not
required, it should be connected directly to the input supply.
While in shutdown, supply current decreases to 0.05 A
(typical) and V
circuited.
ERROR Open Drain Output
lation by more than – 5% (typical). This condition may be
caused by low input voltage, output current limiting, or
thermal limiting. The ERROR threshold is 5% below rated
V
(e.g. ERROR = V
2.85V (typ.) for a 3.0V regulator). ERROR output operation
is shown in Figure 2.
inactive when V
low flag, or as a processor RESET signal (with the addition
of timing capacitor C2). R1 x C2 should be chosen to
maintain ERROR below V
for at least 200msec to allow time for the system to stabilize.
(to CMOS Logic or Tie
OUT
Shutdown Control
to V
The TC1054 is a precision fixed output voltage regula-
Figure 1 shows a typical application circuit. The regula-
ERROR is driven low whenever V
Note that ERROR is active when V
As shown in Figure 1, ERROR can be used as a battery
IN
regardless of the programmed output voltage value
if unused)
IL
IH
BATTERY
. SHDN may be controlled by a CMOS logic gate,
, and shutdown (disabled) when SHDN is at or
1 F
Figure 1. Typical Application Circuit
OUT
OUT
OL
falls to zero volts and ERROR is open
Processor RESET Signal
rises above V
if ERROR is used as a
at 4.75 (typ.) for a 5.0V regulator and
GND
SHDN
OUT
V
C2 Requires Only
IN
TC1054VCT
(See Text)
remains stable and within regula-
IH
of the processor RESET input
ERROR
V
OUT
TH
= V
OUT
OUT
HYS
V
+
1 F
C1
falls out of regu-
falls to V
R1
1M
0.2 F
C2
.
V
OUT
BATTLOW
or RESET
TH
, and
4
Pull-up resistor R1 can be tied to V
voltage less than (V
Output Capacitor
mended. The output capacitor should have an effective
series resistance of 5
above 1MHz. A 1 F capacitor should be connected from
V
the regulator and the AC filter capacitor, or if a battery is
used as the power source. Aluminum electrolytic or tanta-
lum capacitor types can be used. (Since many aluminum
electrolytic capacitors freeze at approximately – 30 C, solid
tantalums are recommended for applications operating
below – 25 C.) When operating from sources other than
batteries, supply-noise rejection and transient response
can be improved by increasing the value of the input and
output capacitors and employing passive filtering tech-
niques.
Thermal Considerations
Thermal Shutdown
tor off when die temperature exceeds 160 C. The regulator
remains off until the die temperature drops to approximately
150 C.
Power Dissipation
rily a function of input and output voltage, and output current.
The following equation is used to calculate worst case
actual power dissipation:
IN
ERROR
50mA CMOS LDO WITH SHUTDOWN
to GND if there is more than 10 inches of wire between
A 1 F(min) capacitor from V
Integrated thermal protection circuitry shuts the regula-
The amount of power the regulator dissipates is prima-
V
OUT
V
V
V
TH
OL
IH
Figure 2. ERROR Output Operation
IN
= 0.3V).
or less, and a resonant frequency
AND ERROR OUTPUT
OUT
OUT
to ground is recom-
, V
HYSTERESIS (V
IN
or any other
HYS
)