LM150QML National Semiconductor, LM150QML Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM150QML
Manufacturer Part Number
LM150QML
Description
LM150 - 3-Amp Adjustable Regulator
Manufacturer
National Semiconductor
Datasheet
1.LM150QML.pdf
(16 pages)
Application Hints
In operation, the LM150 develops a nominal 1.25V reference
voltage, V
The reference voltage is impressed across program resistor
R1 and, since the voltage is constant, a constant current I
then flows through the output set resistor R2, giving an
output voltage of
Since the 50 µA current from the adjustment terminal repre-
sents an error term, the LM150 was designed to minimize
I
do this, all quiescent operating current is returned to the
output establishing a minimum load current requirement. If
there is insufficient load on the output, the output will rise.
EXTERNAL CAPACITORS
An input bypass capacitor is recommended. A 0.1 µF disc or
1 µF solid tantalum on the input is suitable input bypassing
for almost all applications. The device is more sensitive to
the absence of input bypassing when adjustment or output
capacitors are used but the above values will eliminate the
possibility of problems.
The adjustment terminal can be bypassed to ground on the
LM150 to improve ripple rejection. This bypass capacitor
prevents ripple from being amplified as the output voltage is
increased. With a 10 µF bypass capacitor 86 dB ripple
rejection is obtainable at any output level. Increases over
10 µF do not appreciably improve the ripple rejection at
frequencies above 120 Hz. If the bypass capacitor is used, it
is sometimes necessary to include protection diodes to pre-
vent the capacitor from discharging through internal low
current paths and damaging the device.
In general, the best type of capacitors to use is solid tanta-
lum. Solid tantalum capacitors have low impedance even at
high frequencies. Depending upon capacitor construction, it
takes about 25 µF in aluminum electrolytic to equal 1 µF
solid tantalum at high frequencies. Ceramic capacitors are
also good at high frequencies, but some types have a large
decrease in capacitance at frequencies around 0.5 MHz. For
this reason, 0.01 µF disc may seem to work better than a 0.1
µF disc as a bypass.
Although the LM150 is stable with no output capacitors, like
any feedback circuit, certain values of external capacitance
Adj
and make it very constant with line and load changes. To
Ref
, between the output and adjustment terminal.
FIGURE 1.
20155707
1
7
can cause excessive ringing. This occurs with values be-
tween 500 pF and 5000 pF. A 1 µF solid tantalum (or 25 µF
aluminum electrolytic) on the output swamps this effect and
insures stability.
LOAD REGULATION
The LM150 is capable of providing extremely good load
regulation but a few precautions are needed to obtain maxi-
mum performance. The current set resistor connected be-
tween the adjustment terminal and the output terminal (usu-
ally 240Ω) should be tied directly to the output (case) of the
regulator rather than near the load. This eliminates line
drops from appearing effectively in series with the reference
and degrading regulation. For example, a 15V regulator with
0.05Ω resistance between the regulator and load will have a
load regulation due to line resistance of 0.05Ω x I
set resistor is connected near the load the effective line
resistance will be 0.05Ω (1 + R2/R1) or in this case, 11.5
times worse.
Figure 2 shows the effect of resistance between the regula-
tor and 240Ω set resistor.
With the TO-3 package, it is easy to minimize the resistance
from the case to the set resistor, by using two separate leads
to the case. The ground of R2 can be returned near the
ground of the load to provide remote ground sensing and
improve load regulation.
PROTECTION DIODES
When external capacitors are used with any IC regulator it is
sometimes necessary to add protection diodes to prevent
the capacitors from discharging through low current points
into the regulator. Most 10 µF capacitors have low enough
internal series resistance to deliver 20A spikes when
shorted. Although the surge is short, there is enough energy
to damage parts of the IC.
When an output capacitor is connected to a regulator and
the input is shorted, the output capacitor will discharge into
the output of the regulator. The discharge current depends
on the value of the capacitor, the output voltage of the
regulator, and the rate of decrease of V
discharge path is through a large junction that is able to
sustain 25A surge with no problem. This is not true of other
types of positive regulators. For output capacitors of 25 µF or
less, there is no need to use diodes.
The bypass capacitor on the adjustment terminal can dis-
charge through a low current junction. Discharge occurs
when either the input or output is shorted. Internal to the
LM150 is a 50Ω resistor which limits the peak discharge
current. No protection is needed for output voltages of 25V
FIGURE 2. Regulator with Line Resistance
in Output Lead
IN
. In the LM150, this
20155708
www.national.com
OUT
. If the