UPD78F9418A NEC, UPD78F9418A Datasheet - Page 263
UPD78F9418A
Manufacturer Part Number
UPD78F9418A
Description
(UPD7894xxA) 8-Bit Single Chip Microcontrollers
Manufacturer
NEC
Datasheet
1.UPD78F9418A.pdf
(319 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
UPD78F9418A
Manufacturer:
NEC
Quantity:
1 831
Part Number:
UPD78F9418AGC
Manufacturer:
NEC
Quantity:
20 000
Company:
Part Number:
UPD78F9418AGC-8BT-A
Manufacturer:
RENESAS
Quantity:
800
Company:
Part Number:
UPD78F9418AGC-8BT-A
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
UPD78F9418AGK-9EU
Manufacturer:
NEC
Quantity:
20 000
Company:
Part Number:
UPD78F9418AGK-9EU-A
Manufacturer:
Renesas Electronics America
Quantity:
10 000
- Current page: 263 of 319
- Download datasheet (3Mb)
www.DataSheet4U.com
<RESET pin>
reset signal generator on the board, a signal conflict occurs. To prevent this signal conflict, isolate the connection
with the reset signal generator.
operation will not be performed.
programmer during this period.
<Port pins>
programming communication to the status immediately after reset.
status, connect the external device to V
<Oscillation pins>
normal operation mode.
oscillator disconnected, and leave the X2 pin open. For the subclock, connection conforms to that in the normal
operation mode.
<Power supply>
programmer, and the V
because the voltage is monitored by the flash programmer, therefore, VDD of the flash programmer must be
connected.
operation mode.
<Other pins>
operation mode.
When the reset signal of the dedicated flash programmer is connected to the RESET pin connected to the
If a reset signal is input from the user system in the flash memory programming mode, a normal programming
Shifting to the flash memory programming mode sets all the pins except those used for flash memory
Therefore, if the external device does not acknowledge an initial status such as the output high impedance
When using an on-board clock, connection of X1, X2, XT1, and XT2 must conform to the methods in the
When using the clock output of the flash programmer, directly connect it to the X1 pin with the on-board main
To use the power output of the flash programmer, connect the V
To use the on-board power supply, connection must conform to that in the normal operation mode. However,
For the other power supply pins (AV
Handle the other pins (S0 to S15, COM0 to COM3, V
µ
PD78F9418A
SS0
RESET
and V
SS1
Figure 18-7. Signal Conflict (RESET Pin)
In the flash memory programming mode, the signal output
by the reset signal generator and the signal output by the
dedicated flash programmer conflict, therefore, isolate the
signal on the reset signal generator side.
pins to GND of the flash programmer.
Do not input signals other than reset signals from the dedicated flash
DD0
User’s Manual U13952EJ3V0UD
Signal conflict
, V
DD
, AV
DD1
, V
REF
SS0
, AV
, or V
SS
Reset signal generator
SS1
LC0
), supply the same power supply as in the normal
Connection pin of dedicated
flash programmer
via a resistor.
to V
Output pin
LC2
, BIAS) in the same way as in the normal
DD0
and V
DD1
pins to VDD of the flash
263
Related parts for UPD78F9418A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16BIT MCU, 128K FLASH, 8K RAM, SMD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT UC, 32K FLASH, 1KB RAM, LCD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 60K FLASH, 3KB RAM, CAN
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 128K FLASH, 7K RAM, LQFP
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 4K FLASH, 128B RAM, SMD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet: