MIC2583 Micrel Semiconductor, MIC2583 Datasheet - Page 13

• Manufacturer Part Number: MIC2583
• Description: Single Channel Hot Swap Controllers
• Manufacturer: Micrel Semiconductor

Functional Description
Hot Swap Insertion
When circuit boards are inserted into live system backplanes
and supply voltages, high inrush currents can result due to the
charging of bulk capacitance that resides across the supply pins
of the circuit board. This inrush current, although transient in
nature, may be high enough to cause permanent damage to on
board components or may cause the system’s supply voltages
to go out of regulation during the transient period which may
result in system failures. The MIC2582 and MIC2583 act as a
controller for external N-Channel MOSFET devices in which the
gate drive is controlled to provide inrush current limiting and
output voltage slew rate control during hot plug insertions.
Power Supply
VCC is the supply input to the MIC2582/83 controller with a
voltage range of 2.3V to 13.2V. The VCC input can withstand
transient spikes up to 20V. In order to ensure stability of the
supply voltage, a minimum 0.47 F capacitor from VCC to
ground is recommended. Alternatively, a low pass filter, shown
in the typical application circuit (see Figure 1), can be used to
eliminate high frequency oscillations as well as help suppress
transient spikes.
Also, due to the existence of an undetermined amount of
parasitic inductance in the absence of bulk capacitance along
the supply path, placing a Zener diode at the VCC of the
controller to ground in order to provide external supply transient
protection is strongly recommended for relatively high current
applications ( 3A). See Figure 1.
Start-Up Cycle
Supply Contact Delay
During a hot insert of a PC board into a backplane or when the
supply (VCC) is powered up, as the voltage at the ON pin rises
above its threshold (1.24V typical), the MIC2582/83 first checks
that both supply voltages are above their respective UVLO
thresholds. If so, the device is enabled and an internal 2.5 A
current source begins charging capacitor C
initiate a start-up sequence. Once the start-up delay (t
elapses, the CPOR pin is pulled immediately to ground and a
17 A current source begins charging the GATE output to drive
the external MOSFET that switches V
grammed contact start-up delay is calculated using the follow-
ing equation:
where the start-up delay timer threshold (V
the Power-On Reset timer current (I
2 for some typical supply contact start-up delays using several
standard value capacitors. As the GATE voltage continues
ramping toward its final value (V
(See Load Capacitance/Gate Capacitance Dominated Start-
up sections), a second CPOR timing cycle begins if: 1)/FAULT
is high and 2)CFILTER is low (i.e., not an overvoltage,
undervoltage lockout, or overcurrent state). This second timing
cycle (t
threshold (V
is valid. See Figure 3 in the Timing Diagrams. When the power
April 2003
MIC2582/MIC2583
t
START
POR
) begins when the voltage at the FB pin exceeds its
FB
). This condition indicates that the output voltage
C
POR
V
I
START
CPOR
CC
+ V
0.12 C
CPOR
GS
IN
) at a defined slew rate
) is 2.5 A. See Table
START
to V
POR
POR
OUT
( F)
) is 0.3V, and
to 0.3V to
. The pro-
START
(1)
)
13
supply is already present (i.e., not a “hot swapping” condition)
and the MIC2582/83 device is enabled by applying a logic high
signal at the ON pin, the GATE output begins ramping immedi-
ately as the first CPOR timing cycle is bypassed. Active current
regulation is employed to limit the inrush current transient
response during start-up by regulating the load current at the
programmed current limit value (See Current Limiting and Dual-
Level Circuit Breaker section). The following equation is used
to determine the nominal current limit value:
where V
in the electrical table and R
set the desired current limit. There are two basic start-up modes
for the MIC2582/83: 1) Start-up dominated by load capacitance
and 2) start-up dominated by total gate capacitance. The
magnitude of the inrush current delivered to the load will
determine the dominant mode. If the inrush current is greater
than the programmed current limit (I
is dominant. Otherwise, gate capacitance is dominant. The
expected inrush current may be calculated using the following
equation:
where I
capacitance, and C
the external MOSFET and any external capacitor connected
from the MIC2582/83 GATE pin to ground).
Load Capacitance Dominated Start-Up
In this case, the load capacitance (C
cause the inrush current to exceed the programmed current
limit but is less than the fast-trip threshold (or the fast-trip
threshold is disabled, ‘M’ option). During start-up under this
condition, the load current is regulated at the programmed
current limit value (I
voltage rises to its final value. The output slew rate and
equivalent GATE voltage slew rate is computed by the following
equation:
where I
quently, the value of C
the overcurrent response time, t
needed for the output to reach its final value. For example, given
a MOSFET with an input capacitance C
C
load capacitance dominates as determined by the calculated
INRUSH > I
mined from Equation 4 is:
and the resulting t
approximately 4.5ms. (See Power-On Reset and Overcurrent
Timer Delays section to calculate t
Output Voltage Slew Rate, dV
LOAD
I
INRUSH I
Output Voltage Slew Rate, dV
LIM
is 2200 F, and I
GATE
LIM
TRIPSLOW
LIM
is the programmed current limit value. Conse-
V
is the GATE pin pull-up current, C
TRIPSLOW
R
. Therefore, the output voltage slew rate deter-
SENSE
OCSLOW
GATE
is the current limit slow trip threshold found
GATE
LIM
FILTER
LIM
) and held constant until the output
is the total GATE capacitance (C
C
C
is set to 6A with a 12V input, then the
SENSE
needed to achieve a 12V output is
R
LOAD
GATE
50mV
SENSE
must be selected to ensure that
OUT
is the selected value that will
OCSLOW
OCSLOW
LIM
17 A
LOAD
/dt
OUT
), then load capacitance
ISS
/dt
, exceeds the time
MIC2582/MIC2583
) is large enough to
2200 F
= C
)
C
C
6A
LOAD
GATE
GATE
LOAD
C
I
LOAD
LIM
= 4700pF,
is the load
(2)
(3)
2.73
Micrel
ISS
(4)
ms
V
of