LM3409MYX National Semiconductor Corporation, LM3409MYX Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
LM3409MYX
Manufacturer Part Number
LM3409MYX
Description
Pfet Buck Controller For High Power Led Drives
Manufacturer
National Semiconductor Corporation
Datasheet
1.LM3409MYX.pdf
(30 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM3409MYX
Manufacturer:
NS/国半
Quantity:
20 000
AVERAGE LED CURRENT
For a buck converter, the average LED current is simply the
average inductor current.
Using the COFT architecture, the peak transistor current (I
MAX
peak inductor current (I
Because I
set using the controlled off-timer, I
I
The threshold voltage V
parator is affected by the comparator’s input offset voltage,
which causes an error in the calculation of I
mately I
parator inputs is swapped every cycle, which causes the
actual I
and I
in Figure 6. I
LED
FIGURE 6. Inductor Current i
) is sensed as shown in Figure 5, which is equal to the
can be calculated as follows:
L-MAXL
L-MAX
LED
L-MAX
. To mitigate this problem, the polarity of the com-
), equidistant from the theoretical I
LED
FIGURE 5. Sense Voltage v
to alternate between two peak values (I
is set using peak current control and Δi
remains accurate through this averaging.
L-MAX
CST
seen by the high-side sense com-
) given by the following equation:
L
(t) Showing I
L
and correspondingly
SNS
(t)
L-MAX
L-MAX
L-MAX
as shown
and ulti-
Offset
30085612
L-MAXH
L-PP
30085611
T-
is
11
INDUCTOR CURRENT RIPPLE
Because the LM3409/09HV swaps the polarity of the differ-
ential current sense comparator every cycle, a minimum in-
ductor current ripple (Δi
accurate I
terminated at the higher of the two polarity-swapped thresh-
olds (corresponding to I
decreases until the second t
as the second t
current threshold (corresponding to I
t
tion. The minimum inductor current ripple (Δi
adhere to the following equation in order to ensure accurate
I
SWITCHING FREQUENCY
The switching frequency is dependent upon the actual oper-
ating point (V
a given application, therefore the switching frequency will vary
with V
switching frequency (f
selected based on the tradeoffs between efficiency (better at
low frequency) and solution size/cost (smaller at high fre-
quency). The off-time of the LM3409/09HV can be pro-
grammed for switching frequencies up to 5 MHz (theoretical
limit imposed by minimum t
quencies higher than 1MHz may be difficult to obtain due to
gate drive limitations, high input voltage, and thermal consid-
erations.
At CCM operating points, f
At DCM operating points, f
In the CCM equation, it is apparent that the efficiency (η) fac-
tors into the switching frequency calculation. Efficiency is hard
to estimate and, since switching frequency varies with input
voltage, accuracy in setting the nominal switching frequency
is not critical. Therefore, a general rule of thumb for the
LM3409/09HV is to assume an efficiency between 85% and
100%. When approximating efficiency to target a nominal
switching frequency, the following condition must be met:
ON
LED
pulse will follow. This will result in degraded I
regulation:
IN
(frequency increases as V
LED
IN
regulation. Referring to Figure 6, the first t
ON
and V
begins, i
O
SW
). V
L-MAXH
) at the nominal operating point is
O
L
SW
SW
L-PP
ON
will remain relatively constant for
will still be above the lower peak
ON
is defined as:
is defined as:
) is necessary to maintain
). During the following t
begins. If t
). In practice, switching fre-
IN
L-MAXL
increases). The target
OFF
) and a minimum
is too short, then
L-PP-MIN
www.national.com
LED
) should
regula-
OFF
ON
, i
is
L