LTC2498 Linear Technology, LTC2498 Datasheet - Page 26
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LTC2498
Manufacturer Part Number
LTC2498
Description
24-Bit 8-/16-Channel ADC
Manufacturer
Linear Technology
Datasheet
1.LTC2498.pdf
(36 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC2498CUHF
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC2498CUHF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC2498CUHF#PBF/IU
Manufacturer:
LT
Quantity:
444
Company:
Part Number:
LTC2498HUHF
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC2498IUHF
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC2498IUHF#PBF/CU
Manufacturer:
LT
Quantity:
503
www.DataSheet4U.com
APPLICATIONS INFORMATION
LTC2498
The input data is shifted through the SDI pin on the ris-
ing edge of SCK (including the fi rst rising edge) and the
output data is shifted out the SDO pin on the falling edge
of SCK. The data input/output cycle is concluded and a
new conversion automatically begins after the 32nd rising
edge of SCK. During the next conversion, SCK and SDO
remain HIGH until the conversion is complete.
The Use of a 10k Pull-Up on SCK for Internal SCK
Selection
If CS is pulled HIGH while the converter is driving SCK
LOW, the internal pull-up is not available to restore SCK
to a logic HIGH state if SCK is fl oating. This will cause the
device to exit the internal SCK mode on the next falling
edge of CS. This can be avoided by adding an external 10k
pull-up resistor to the SCK pin.
Whenever SCK is LOW, the LTC2498’s internal pull-up at
SCK is disabled. Normally, SCK is not externally driven if
the device is operating in the internal SCK timing mode.
However, certain applications may require an external
driver on SCK. If the driver goes Hi-Z after outputting a
LOW signal, the internal pull-up is disabled. An external
10k pull-up resistor prevents the device from exiting the
internal SCK mode under this condition.
A similar situation may occur during the sleep state when
CS is pulsed HIGH-LOW-HIGH in order to test the conver-
sion status. If the device is in the sleep state (EOC = 0),
SCK will go LOW. If CS goes HIGH before the time t
the internal pull-up is activated. If SCK is heavily loaded,
the internal pull-up may not restore SCK to a HIGH state
before the next falling edge of CS. The external 10k pull-up
resistor prevents the device from exiting the internal SCK
mode under this condition.
PRESERVING THE CONVERTER ACCURACY
The LTC2498 is designed to reduce as much as possible
sensitivity to device decoupling, PCB layout, anti-aliasing
circuits, line frequency perturbations, and temperature
sensitivity. In order to achieve maximum performance a
few simple precautions should be observed.
26
EOCtest
,
Digital Signal Levels
The LTC2498’s digital interface is easy to use. Its digital
inputs (SDI, F
accept standard CMOS logic levels. Internal hysteresis
circuits can tolerate edge transition times as slow as
100μs.
The digital input signal range is 0.5V to V
transitions, the CMOS input circuits draw dynamic cur-
rent. For optimal performance, application of signals to
the serial data interface should be reserved for the sleep
and data output periods.
During the conversion period, overshoot and undershoot
of fast digital signals applied to both the serial digital in-
terface and the external oscillator pin (F
the converter performance. Undershoot and overshoot
occur due to impedance mismatch of the circuit board
trace at the converter pin when the transition time of an
external control signal is less than twice the propagation
delay from the driver to the input pin. For reference, on a
regular FR-4 board, the propagation delay is approximately
183ps/inch. In order to prevent overshoot, a driver with
a 1ns transition time must be connected to the converter
through a trace shorter than 2.5 inches. This becomes
diffi cult when shared control lines are used and multiple
refl ections occur.
Parallel termination near the input pin of the LTC2498 will
eliminate this problem, but will increase the driver power
dissipation. A series resistor from 27Ω to 54Ω (depend-
ing on the trace impedance and connection) placed near
the driver will also eliminate over/under shoot without
additional driver power dissipation.
For many applications, the serial interface pins (SCK, SDI,
CS, F
no degradation occurs. On the other hand, if an external
oscillator is used (F
the conversion cycle. Moreover, the digital fi lter rejection
is minimal at the clock rate applied to F
taken to ensure external inputs and reference lines do not
cross this signal or run near it. These issues are avoided
when using the internal oscillator.
O
) remain static during the conversion cycle and
O
, CS, and SCK in external serial clock mode)
O
driven externally) it is active during
CC
O
O
. Care must be
) may degrade
– 0.5V. During
2498fc