LTC3589 Linear Technology, LTC3589 Datasheet - Page 15

• Manufacturer Part Number: LTC3589
• Description: 8-Output Regulator
• Manufacturer: Linear Technology

OPERATION
INTRODUCTION
The LTC3589 is a complete power management solution
for portable microprocessors and peripheral devices. It
generates a total of eight voltage rails for supplying power
to the processor core, SDRAM, system memory, PC cards,
always-on real time clock and HDD functions. Supplying
the voltage rails are an always-on low quiescent current
25mA LDO, one 1.6A and two 1A step-down regulators, a
1.2A buck-boost regulator, and three 250mA low dropout
regulators. Supporting the multiple regulators is a highly
confi gurable power-on sequencing capability, dynamic
voltage slewing DAC output voltage control, a pushbutton
interface controller, regulator control via an I
and extensive status and interrupt outputs.
The LTC3589 operates over an input supply range of 2.7V
to 5.5V. The input supplies for the 250mA LDO regulators
may operate as low as 1.7V to limit power loss at low
output voltages.
The always-on LDO1 provides a resistor programmable
output voltage as low as 0.8V and is capable of supplying
25mA. With only the always-on LDO active the LTC3589
draws just 10μA (typical). Always on LDO1 will continue to
operate with V
memory and RTC function as long as possible.
Each of the 250mA LDO regulators has unique output volt-
age confi gurations. LDO3 has a fi xed 1.8V output. LDO4
has four output levels selectable via the I
Its possible outputs are 1.8V, 2.5V, 2.8V, and 3.3V. LDO2
has a dynamically slewing DAC set point reference and
an external feedback pin to set the output voltage range
with a resistive divider. Each LDO draws 60μA (typical)
quiescent current.
The LTC3589 includes three internally compensated
constant frequency current mode step-down switching
regulators providing 1A, 1A, and 1.6A. Step-down regula-
tor switching frequencies of 2.25MHz or 1.125MHz are
independently selected for each step-down regulator
using the I
frequency is 2.25MHz. Each of the step-down regulators
have dynamically slewing DAC input references and external
feedback pins to set output voltage range. The step-down
regulators three operating modes, pulse-skipping, burst,
2
C command registers. The power-on default
IN
levels as low as 2.0V (typical) to maintain
2
2
C interface.
C interface,
or forced continuous, are set using the I
pulse-skipping mode the regulator will support 100%
duty cycle. For best effi ciency at low output loads select
Burst Mode operation. Forced continuous mode minimizes
output voltage ripple at light loads.
The 4-switch buck-boost DC/DC voltage mode converter
generates a user-programmable output voltage rail from
2.5V to 5V. Utilizing a proprietary switching algorithm,
the buck-boost converter maintains high effi ciency and
low noise operation with input voltages that are above,
below or equal to the required output rail. The buck-boost
error amplifi er uses a fi xed 0.8V reference and the output
voltage is set by an external resistor divider. Burst Mode
operation is enabled through the I
external compensation components are required for the
buck-boost converter.
The reference inputs for the three step-down regulators
and LDO2 are 5-bit D to A converters with up-down ramp-
ing at selectable slew rates. The slew endpoint voltages
and select bits are stored in I
A select bit in the I
register to use for each target voltage. Variable reference
slew rates from 0.88mV/μs to 7mV/μs are selectable in
the I
voltage, voltage select, and slew rate control registers.
The LTC3589 is equipped with a pushbutton control circuit
that will activate the WAKE output, indicate pushbutton
status via the PBSTAT pin, and initiate a hard reset shut-
down of the regulators. Grounding the ON pin with the
pushbutton for 400ms will force the WAKE pin to release
HIGH. The WAKE pin output can be tied to the enable pin
of the fi rst regulator in a power-on sequence. Once in the
power-on state, subsequent pushes of the button longer
than 50ms are mirrored by the PBSTAT output. Holding
ON LOW for fi ve seconds disables all the regulators, pulls
down the WAKE pin, and pulls down RSTO for one second
to indicate to the processor that a hard reset occurred. All
regulator enables and pushbutton inputs are inhibited for
one second following the hard reset.
The LTC3589 has fl exible options for enabling and sequenc-
ing the regulator enables. The regulators are enabled us-
ing input pins or the I
2
C register. Each of the four DACs has independent
2
C command registers chooses which
2
C serial port. To defi ne a power-on
2
C registers for each DAC.
2
C control registers. No
www.DataSheet4U.com
LTC3589
2
C interface. In
15
3589p