ds2154lnd2 Maxim Integrated Products, Inc., ds2154lnd2 Datasheet - Page 30
ds2154lnd2
Manufacturer Part Number
ds2154lnd2
Description
Ds2154 Enhanced E1 Single Chip Transceiver
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.DS2154LND2.pdf
(87 pages)
- Current page: 30 of 87
- Download datasheet (2Mb)
DS2154
4.4 Power-Up Sequence
On power-up, after the supplies are stable, the DS2154 should be configured for operation by writing to
all of the internal registers (this includes the Test Registers) since the contents of the internal registers
cannot be predicted on power-up. Next, the LIRST (CCR5.7) bit should be toggled from 0 to 1 to reset
the line interface circuitry (it will take the DS2154 about 40ms to recover from the LIRST bit being
toggled). Finally, after the RSYSCLK and TSYSCLK inputs are stable, the ESR bit should be toggled
from a 0 to a 1 and then back to 0 (this step can be skipped if the elastic stores are not being used). Both
TCLK and RCLKI must be present for the parallel control port to operate properly.
4.5 Automatic Alarm Generation
When either CCR2.4 or CCR2.5 is set to 1, the DS2154 monitors the receive side to determine if any of
the following conditions are present: loss of receive frame synchronization, AIS alarm (all 1s) reception,
or loss of receive carrier (or signal). If any one (or more) of the above conditions is present, then the
DS2154 will either force an AIS alarm (if CCR2.5 = 1) or a Remote Alarm (CCR2.4 = 1) to be
transmitted via the TPOSO and TNEGO pins. It is an illegal state to have both CCR2.4 and CCR2.5 set to
1 at the same time. If CCR2.4 = 1, then RAI will be transmitted according to ETS 300 011 specifications
and a constant Remote Alarm will be transmitted if the DS2154 cannot find CRC4 multiframe
synchronization within 400ms as per G.706.
30 of 87
Related parts for ds2154lnd2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
power light source Luxeon Line
Manufacturer:
LUMILEDS [Lumileds Lighting Company]
Datasheet:
Part Number:
Description:
Nonvolatile Ram Controller Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
3.3v Single-piece 8mb Nonvolatile Sram Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Pon Triplexer Control And Monitoring Circuit Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Ttl Compatible Cmos Analog Switches Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Improved Low-power, Cmos Analog Switches With Latches Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
4a, 20ns, Dual Mosfet Drivers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Nicd/nimh Battery Fast-charge Controllers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
3.6v, 1w Autoramping Power Amplifier For 900mhz Applications Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
2.7v, Single-supply, Cellular-band Linear Power Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
5ghz Linear Power Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Evaluation Kits for the MAX3514
Manufacturer:
Maxim Integrated Products, Inc.
Part Number:
Description:
Accurate I2c Rtc With Integrated Tcxo/crystal/fram
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Ds1863 Burst-mode Pon Controller With Integrated Monitoring
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet: