ltc2226iuh-trpbf Linear Technology Corporation, ltc2226iuh-trpbf Datasheet - Page 22

• Manufacturer Part Number: ltc2226iuh-trpbf
• Description: Ltc2227 - 12-bit, 40msps Low Power 3v Adcs
• Manufacturer: Linear Technology Corporation

LTC2228/LTC2227/LTC2226
APPLICATIO S I FOR ATIO
Data Format
Using the MODE pin, the LTC2228/LTC2227/LTC2226
parallel digital output can be selected for offset binary or
2’s complement format. Connecting MODE to GND or
1/3V
MODE to 2/3V
format. An external resistor divider can be used to set the
1/3V
states for the MODE pin.
Overflow Bit
When OF outputs a logic high the converter is either
overranged or underranged.
Output Driver Power
Separate output power and ground pins allow the output
drivers to be isolated from the analog circuitry. The power
supply for the digital output buffers, OV
to the same power supply as for the logic being driven. For
example if the converter is driving a DSP powered by a 1.8V
supply, then OV
OV
3.6V. OGND can be powered with any voltage from GND up
to 1V and must be less than OV
swing between OGND and OV
Output Enable
The outputs may be disabled with the output enable pin, OE.
OE high disables all data outputs including OF. The data ac-
cess and bus relinquish times are too slow to allow the
outputs to be enabled and disabled during full speed op-
eration. The output Hi-Z state is intended for use during long
periods of inactivity.
Sleep and Nap Modes
The converter may be placed in shutdown or nap modes
to conserve power. Connecting SHDN to GND results in
normal operation. Connecting SHDN to V
results in sleep mode, which powers down all circuitry
including the reference and typically dissipates 1mW. When
exiting sleep mode it will take milliseconds for the output
22
DD
DD
DD
can be powered with any voltage from 500mV up to
selects offset binary output format. Connecting
or 2/3V
DD
DD
DD
or V
should be tied to that same 1.8V supply.
logic values. Table 2 shows the logic
U
DD
selects 2’s complement output
U
DD
DD
.
. The logic outputs will
W
DD
DD
, should be tied
and OE to V
U
DD
data to become valid because the reference capacitors have
to recharge and stabilize. Connecting SHDN to V
to GND results in nap mode, which typically dissipates
15mW. In nap mode, the on-chip reference circuit is kept
on, so that recovery from nap mode is faster than that from
sleep mode, typically taking 100 clock cycles. In both sleep
and nap modes, all digital outputs are disabled and enter
the Hi-Z state.
Grounding and Bypassing
The LTC2228/LTC2227/LTC2226 require a printed circuit
board with a clean, unbroken ground plane. A multilayer
board with an internal ground plane is recommended.
Layout for the printed circuit board should ensure that
digital and analog signal lines are separated as much as
possible. In particular, care should be taken not to run any
digital track alongside an analog signal track or under-
neath the ADC.
High quality ceramic bypass capacitors should be used at
the V
tors must be located as close to the pins as possible. Of
particular importance is the 0.1µF capacitor between
REFH and REFL. This capacitor should be placed as close
to the device as possible (1.5mm or less). A size 0402
ceramic capacitor is recommended. The large 2.2µF ca-
pacitor between REFH and REFL can be somewhat further
away. The traces connecting the pins and bypass capaci-
tors must be kept short and should be made as wide as
possible.
The LTC2228/LTC2227/LTC2226 differential inputs should
run parallel and close to each other. The input traces
should be as short as possible to minimize capacitance
and to minimize noise pickup.
Heat Transfer
Most of the heat generated by the LTC2228/LTC2227/
LTC2226 is transferred from the die through the bottom-
side exposed pad and package leads onto the printed
circuit board. For good electrical and thermal perfor-
mance, the exposed pad should be soldered to a large
grounded pad on the PC board. It is critical that all ground
pins are connected to a ground plane of sufficient area.
DD
, OV
DD
, V
CM
, REFH, and REFL pins. Bypass capaci-
DD
and OE
222876fa