nt39016d Newhaven Display International, Inc, nt39016d Datasheet - Page 8

• Manufacturer Part Number: nt39016d
• Description: One Chip Tft Lcd Driver Ic With Timing Controller For S960xg240 Tft Lcd
• Manufacturer: Newhaven Display International, Inc

NT39016 Pad Description:
With respect to the information represented in this document, Novatek makes no warranty, expressed or implied, including the warranties of merchantability,
fitness for a particular purpose, non-infringement, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any such
information.
Pad Description
GO1~GO240
Designation
SO1~SO960
ALIGN_T/B
DIN[23..0]
PINCTLB
Mar 10,2008
DATSEQ
TP16~18
V1 ~ V7
TP0~14
SPENB
CLKIN
SPSW
VPSW
SPDA
SPCK
RSTB
TP15
HSD
VSD
DEN
POL
(Pull High)
(Pull High)
(Pull High)
(Pull Low)
(Pull Low)
(Pull Low)
I/O
I/O
I/O
M
O
O
O
O
T
I
I
I
I
I
I
I
I
I
I
I
I
I
Data Input. For 8/24-bit digital (RGB) or 8-bit CCIR601/656 image data input
8-bit mode: DIN7: MSB; DIN0: LSB; the remainder should be connect to GND.
24-bit mode: DIN[7:0] = R[7:0] data; DIN[15:8] = G[7:0] data; DIN[23:16] = B[7:0] data.
For 18bit RGB interface, connect two LSB bits of all the R/G/B data bus to GND.
Clock for Input Data. Data latched at rising/falling edge of this signal. Default Negative
polarity.
Horizontal Sync input. Default Negative polarity, can be change by HSDPOL register.
Vertical Sync input. Default Negative polarity, can be change by VSDPOL register.
Data Input Enable. Active High to enable the data input Bus under “DE Mode”. Normally
pull low.
Data sequence control pin for external T-CON.
Output “1”: for Odd line, “0”: for Even line
Frame polarity output. Amplitude of signal is from 0V to 3.3V.
Gamma correction reference voltage.
When VSET=”1” is used. The voltage of pins V1 ~ V7 must be swing and must be
AVDD-0.1V > V1 > V2 > V3
AGND+0.1V < V1’ < V2’ < V3’
Where V1-V2=V2’-V1’, V2-V3=V3’-V2’, …V5-V6=V6’-V5’, V6-V7=V7’-V6’.
Note: V1~V7 must be supplied voltage external when VSET=”1”. Vx is external power of
positive polarity and Vx’ is external power of negative polarity
3-Wire Communication Enable. Active Low. Normally pull high.
Please pull high or floating under PINCTLB=0 mode.
3-Wire Communication Data input/output.
3-Wire Communication Clock input. Rising edge latch.
3-Wire register map select.
”0” for default 3-Wire register map, “1” for optional 3-Wire register map.
Global reset pin. Active Low to enter Reset State. Suggest connecting with a RC reset
circuit for stability. Normally pull high.
Enable pin control function. Normally pull high
PINCTLB = “0”, Enable pin control function.
function control propose. Refer to the TP0~18 description for more information.
PINCTLB = “1”, Default mode.
connect
Note: The 3-wire control register will be disabled under PINCTLB = 0 mode.
Source Driver Output Signals.
Gate Driver Output Signals.
For assembly alignment.
Charge pump on/off control pin.TP15=CPMPDB
CPMPDB = “0”, internal charge pump will be shut down
CPMPDB = “1”, internal charge pump normal operating
TP15 active as input pin under any state of PINCTLB.
If floating TP15,the charge pump will turn off
TEST Pin / Function control pin.
When PINCTLB = “1”, TP0~14, TP16~18 act as test pin. Floating those pins for normal
operation.
When PINCTLB = “0”, TP0~14, TP16~18 act as function control input pin. All the input pin
should be connect to GND or VDD. Floating those pins will result in input unknown
problem.
Voltage control switch. Normally pull low.
VPSW = “0” .Default mode. VGH
control by 3-wire.
VPSW = “1”.Voltage fix mode. VGH = 18V
TP0~14 and TP16~18
V5 > V6 > V7 > AGND+0.1V when POL=”1” and
8
to any state under this mode.
、
TP0~14 and TP16~18
V5’ < V6’ < V7’ < AVDD-0.1V when POL=”0”,
V GL
、
Description
Preliminary Spec. for NT39016D
V COMAC and VCOMDC active as normal use and
、
V GL = -7V
TP0~14 and TP16~18
、
active as unknown state ; Don’t
V COMAC = 5.4V and VCOMDC
active as input pin for
TFT LCD Driver
Version 0.7