cy7c1380b-200bzc Cypress Semiconductor Corporation., cy7c1380b-200bzc Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/1/180/cypress_semiconductor_corporation__sml.jpg)
cy7c1380b-200bzc
Manufacturer Part Number
cy7c1380b-200bzc
Description
512k X 36/1m X 18 Pipelined Sram
Manufacturer
Cypress Semiconductor Corporation.
Datasheet
1.CY7C1380B-200BZC.pdf
(34 pages)
IEEE 1149.1 Serial Boundary Scan (JTAG)
The CY7C1380B/CY7C1382B incorporates a serial boundary
scan Test Access Port (TAP) in the FBGA package only. The
TQFP package does not offer this functionality. This port oper-
ates in accordance with IEEE Standard 1149.1-1900, but does
not have the set of functions required for full 1149.1 compli-
ance. These functions from the IEEE specification are exclud-
ed because their inclusion places an added delay in the critical
speed path of the SRAM. Note that the TAP controller func-
tions in a manner that does not conflict with the operation of
other devices using 1149.1 fully compliant TAPs. The TAP op-
erates using JEDEC standard 3.3V I/O logic levels.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(V
nally pulled up and may be unconnected. They may alternately
be connected to V
be left unconnected. Upon power-up, the device will come up
in a reset state which will not interfere with the operation of the
device.
Test Access Port (TAP) - Test Clock
The test clock is used only with the TAP controller. All inputs
are captured on the rising edge of TCK. All outputs are driven
from the falling edge of TCK.
Test Mode Select
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to
leave this pin unconnected if the TAP is not used. The pin is
pulled up internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI pin is used to serially input information into the regis-
ters and can be connected to the input of any of the registers.
The register between TDI and TDO is chosen by the instruc-
tion that is loaded into the TAP instruction register. For infor-
mation on loading the instruction register, see the TAP Control-
ler State Diagram. TDI is internally pulled up and can be
unconnected if the TAP is unused in an application. TDI is con-
nected to the Most Significant Bit (MSB) on any register.
Test Data Out (TDO)
The TDO output pin is used to serially clock data-out from the
registers. The e output is active depending upon the current
state of the TAP state machine (see TAP Controller State
Diagram). The output changes on the falling edge of TCK.
TDO is connected to the Least Significant Bit (LSB) of any
register.
Performing a TAP Reset
A Reset is performed by forcing TMS HIGH (VDD) for five ris-
ing edges of TCK. This RESET does not affect the operation
of the SRAM and may be performed while the SRAM is oper-
ating. At power-up, the TAP is reset internally to ensure that
TDO comes up in a high-Z state.
TAP Registers
Registers are connected between the TDI and TDO pins and
allow data to be scanned into and out of the SRAM test circuit-
Document #: 38-05267 Rev. *A
SS
) to prevent clocking of the device. TDI and TMS are inter-
DD
through a pull-up resistor. TDO should
ry. Only one register can be selected at a time through the
instruction registers. Data is serially loaded into the TDI pin on
the rising edge of TCK. Data is output on the TDO pin on the
falling edge of TCK.
Instruction Register
Three-bit instructions can be serially loaded into the instruc-
tion register. This register is loaded when it is placed between
the TDI and TDO pins as shown in the TAP Controller Block
Diagram. Upon power-up, the instruction register is loaded
with the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as de-
scribed in the previous section.
When the TAP controller is in the CaptureIR state, the two least
significant bits are loaded with a binary “01” pattern to allow
for fault isolation of the board level serial test path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain states. The bypass
register is a single-bit register that can be placed between TDI
and TDO pins. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW
(VSS) when the BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all the input and
output pins on the SRAM. Several no connect (NC) pins are
also included in the scan register to reserve pins for higher
density devices. The x36 configuration has a xx-bit-long regis-
ter, and the x18 configuration has a yy-bit-long register.
The boundary scan register is loaded with the contents of the
RAM Input and Output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and
TDO pins when the controller is moved to the Shift-DR state.
The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instruc-
tions can be used to capture the contents of the Input and
Output ring.
The Boundary Scan Order tables show the order in which the
bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected
to TDI, and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP controller
is in the Shift-DR state. The ID register has a vendor code and
other information described in the Identification Register Defi-
nitions table.
TAP Instruction Set
Eight different instructions are possible with the three-bit in-
struction register. All combinations are listed in the Instruction
Code table. Three of these instructions are listed as RE-
SERVED and should not be used. The other five instructions
are described in detail below.
The TAP controller used in this SRAM is not fully compliant to
the 1149.1 convention because some of the mandatory 1149.1
instructions are not fully implemented. The TAP controller can-
not be used to load address, data or control signals into the
CY7C1380B
CY7C1382B
Page 12 of 34