pca82c252 NXP Semiconductors, pca82c252 Datasheet
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
pca82c252
Available stocks
Related parts for pca82c252
pca82c252 Summary of contents
Page 1
... DATA SHEET PCA82C252 Fault-tolerant CAN transceiver Product specification Supersedes data of 1997 Mar 07 File under Integrated Circuits, IC18 INTEGRATED CIRCUITS 1997 Oct 28 ...
Page 2
... Low current sleep/standby mode with wake-up via the bus lines Power-on reset flag on the output. GENERAL DESCRIPTION The PCA82C252 is the interface between the CAN protocol controller and the physical bus primarily intended for low-speed applications 125 kBaud, in passenger cars. The device provides differential transmit capability but will switch in error conditions to a single-wire transmitter and/or receiver ...
Page 3
... STB TXD 4 NERR 3 RXD 13 GND 1997 Oct 28 BAT 14 TEMPERATURE WAKE-UP PROTECTION STANDBY CONTROL DRIVER PCA82C252 FAILURE DETECTOR PLUS WAKE UP PLUS TIME-OUT RECEIVER Fig.1 Block diagram. 3 Product specification PCA82C252 RTL 11 CANH 12 CANL 8 RTH FILTER FILTER MBH548 ...
Page 4
... LOW in dominant state GND 13 ground BAT 14 battery voltage handbook, halfpage INH 1 TXD 2 RXD 3 4 PCA82C252 NERR STB WAKE MBG621 Fig.2 Pin configuration. 1997 Oct 28 DESCRIPTION 14 BAT 13 GND 12 CANL 11 CANH RTL 8 RTH 4 Product specification PCA82C252 ...
Page 5
... Philips Semiconductors Fault-tolerant CAN transceiver FUNCTIONAL DESCRIPTION The PCA82C252 is the interface between the CAN protocol controller and the physical bus primarily intended for low speed applications 125 kbaud, in passenger cars. The device provides differential transmit capability to the bus and differential receive capability to the CAN controller ...
Page 6
... LOW active wake-up interrupt signal if V floating floating HIGH LOW active V BAT power-on flag HIGH LOW active error fl Product specification PCA82C252 RXD is present switched switched to V switched to V LOW active wake-up switched to V interrupt HIGH = receive; switched to V LOW = dominant ...
Page 7
... T vj amb . The rating for T limits the allowable combinations vj vj resistor. CONDITIONS VALUE 120 7 Product specification PCA82C252 MAX. UNIT +6 0 +27 V +40 V +100 0.3 V BAT 0.3 V BAT + ...
Page 8
... 100 250 1. WAKE BAT STB 8 Product specification PCA82C252 MIN. TYP 120 0. 100 320 2. 120 1 ...
Page 9
... CANL TXD = 0 V CANH sleep mode CANH TXD = 0 V CANL sleep mode CANL BAT normal mode standby/sleep mode failures 4, 6 and 7 failure 3 9 Product specification PCA82C252 MIN. TYP. MAX. UNIT 0.8 V 1.0 V 5.0 3.25 2.65 V 0.4 0.7 1.0 V 3.25 2. 0.2 V ...
Page 10
... 3.3 nF 100 ; no failures and bus failures 1, 2 and 100 pF 100 ; bus failures and 3.3 nF 100 ; bus failures and 7 10 Product specification PCA82C252 MIN. TYP. MAX. UNIT ...
Page 11
... BAT low power modes BAT normal mode normal mode normal mode normal mode normal mode = 12 V 0.8 BAT = 12 V BAT normal mode normal mode 11 Product specification PCA82C252 MIN. TYP. MAX. UNIT 0.75 1.25 1 1.5 0.85 1.3 1.4 2 ...
Page 12
... WAKE 7 TXD 2 STB PCA82C252 RXD GND NERR Fig.3 Test circuit for dynamic characteristics. t PD(L) Fig.4 Timing diagram for dynamic characteristics. 12 Product specification PCA82C252 R1 C1 RTH 8 CANL 12 C2 CANH 11 RTL MBH550 per transceiver is allowed 3 ...
Page 13
... P8xC292/P8xCE598 CAN CONTROLLER CTX0 CRXO TXD RXD STB NERR PCA82C252 CAN TRANSCEIVER RTH CANH CANL CAN BUS LINE Fig.5 Application of the PCA82C252 INH BAT WAKE 7 TXD 2 12 STB PCA82C252 RXD GND NERR Fig ...
Page 14
... REFERENCES JEDEC EIAJ MS-012AB detail 1.0 0.7 1.05 0.25 0.25 0.4 0.6 0.039 0.028 0.041 0.01 0.01 0.016 0.024 EUROPEAN PROJECTION Product specification PCA82C252 SOT108 ( 0.7 0.1 0 0.028 0.004 0.012 ISSUE DATE 95-01-23 97-05-22 ...
Page 15
... Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 15 Product specification PCA82C252 ...
Page 16
... Philips customers using or selling these products for use in such applications their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1997 Oct 28 16 Product specification PCA82C252 ...
Page 17
... Philips Semiconductors Fault-tolerant CAN transceiver 1997 Oct 28 NOTES 17 Product specification PCA82C252 ...
Page 18
... Philips Semiconductors Fault-tolerant CAN transceiver 1997 Oct 28 NOTES 18 Product specification PCA82C252 ...
Page 19
... Philips Semiconductors Fault-tolerant CAN transceiver 1997 Oct 28 NOTES 19 Product specification PCA82C252 ...
Page 20
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 160 1010, ...