hi5710a Intersil Corporation, hi5710a Datasheet
hi5710a
Related parts for hi5710a
hi5710a Summary of contents
Page 1
... LSB. The low power, high speed and small package outline make the HI5710A an ideal choice for CCD, battery, and high channel count applications. The HI5710A does not require an external sample and hold but requires an external reference and includes force and sense reference pins for increased accuracy ...
Page 2
... AMP COURSE COMPARATOR AND ENCODE CLK 22 TIMING GEN HI5710A + DAC FINE COMPARATOR AND ENCODE CALIBRATION UNIT AUTO CALIBRATION PULSE GENERATOR 4-1532 12 D9 (MSB COURSE CORRECTION 10 D7 AND LATCH ...
Page 3
... Minimum Conversion Speed Effective Number of Bits, ENOB Signal to Noise and Distortion, SINAD Spurious Free Dynamic Range, SFDR Differential Gain Error, DG Differential Phase Error, DP HI5710A o Thermal Information C Thermal Resistance (Typical, Note 0.5V MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
... PZH t PHZ Sampling Delay POWER SUPPLY CHARACTERISTIC Analog Supply Current Digital Supply Current Analog Standby Current Digital Standby Current NOTE: 2. Electrical specifications guaranteed only under the stated operating conditions. HI5710A = +5V +3.3V 2.0V TEST CONDITIONS ...
Page 5
... ANALOG INPUT xxxxxxxx xxxxxxxx DATA OUTPUT INDICATES POINT AT WHICH ANALOG DATA IS SAMPLED 1.65V (DV = 3.3V) DD 2.5V (DV = 5.0V) DD OUTPUT ENABLE (OE) DATA OUTPUT ACTIVE HI5710A ...
Page 6
... OR MORE CLK 1 CLOCK OR MORE CAL FIGURE 3. EXTERNAL CALIBRATION PULSE TIMING DIAGRAM INPUT CLK CAL INPUT CLK CAL FIGURE 4. EXAMPLES OF EXTERNAL CALIBRATION PULSE INPUT FOR VIDEO APPLICATIONS HI5710A 7 CLOCKS FIGURE 4A. CALIBRATION DURING H SYNC FIGURE 4B. CALIBRATION DURING V SYNC 4-1536 ...
Page 7
... 20MHz P 0.1 1 INPUT FREQUENCY (MHz) FIGURE 9. SINAD vs INPUT FREQUENCY HI5710A 100 o C) FIGURE 6. MAXIMUM OPERATING FREQUENCY vs AMBIENT TEMPERATURE 1MHz - FIGURE 8. SAMPLING DELAY vs AMBIENT TEMPERATURE ...
Page 8
... INPUT VOLTAGE (V) FIGURE 13. ANALOG INPUT CURRENT vs INPUT VOLTAGE -25 -30 -35 -40 -45 -50 - 3.3V DD -60 -65 -70 -75 0.1 1 INPUT FREQUENCY (MHz) FIGURE 15. THD vs INPUT FREQUENCY HI5710A (Continued 5. 20MHz 100 100K FIGURE 12 ...
Page 9
... CLK AV 41 CAL AV 15 RESET AV 14 TIN HI5710A EQUIVALENT CIRCUIT Digital Outputs: D0 (LSB (MSB). Test Pin, Leave Pin Open. Digital V Digital V Analog V Controls calibration input pulse selection after DD completion of the internal start-up calibration function. High: Selects the internal auto calibration pulse ...
Page 10
... TSTR TESTMODE AV 20 LINV AV HI5710A (Continued) EQUIVALENT CIRCUIT Reference Top, normally 4.0V Reference Bottom, normally 2.0V Factory Test Signal Output, leave pin open. Factory Test Signal Input, tie to AV Factory Test Signal Input, tie Output Enable. ...
Page 11
... NOTES: 4. This table shows the output state for the combination of TESTMODE, LINV, and MINV states Non-Inverted Output Inverted Output. HI5710A (Continued) EQUIVALENT CIRCUIT Output Inversion. DD High inverted. Low normal Analog V Analog Input. ...
Page 12
... The HI5710A samples the input signal on the rising edge of the clock with the digital data being latched at the digital outputs (D0 - D9) after 3 clock cycles. The HI5710A is designed for use with a 50% duty cycle square wave, but a 10% variation should not affect performance. ...
Page 13
... HI5710A External Calibration Pulse Input Function If the auto calibration pulse generation function cannot be used then periodic calibration can be performed by providing externally input calibration pulses to the CAL input pin (pin 41) and setting the SEL control input pin (pin 17) low ...
Page 14
... COMPARATOR 10 10 DUT A10 B10 HI5710A “0” “1” CLK (20MHz) CONTROLLER 4.0V 2. DUT AMP HI5710A FIGURE 19. DIGITAL OUTPUT TEST CIRCUIT 4-1544 BUFFER 000 • • • 111 • • • 10 SCOPE 1 10 ...
Page 15
... COUNTER CO CLR CLR 24-BIT COUNTER CO CLR SEL CAL - + HI5710A +3.3VD 0.1 DIGITAL OUTPUTS 4-1545 OUT +5VA 0 CLK ...
Page 16
... FIGURE 21B. POWER-UP CALIBRATION WITH EXTERNAL CALIBRATION PULSE INPUT SELECTED HI5710A (Continued HI5710A +3.3VD 0.1 DIGITAL OUTPUTS 4-1546 +5VA 0 ...
Page 17
... FIGURE 21C. ONLY POWER-UP CALIBRATION BEING UTILIZED HI5710A (Continued HI5710A +3.3VD 0.1 DIGITAL OUTPUTS 4-1547 +5VA 0 ...
Page 18
... HI5710A Dynamic Performance Definitions Fast Fourier Transform (FFT) techniques are used to evaluate the dynamic performance of the HI5710A. A low distortion sine wave is applied to the input sampled, and the output is stored in RAM. The data is then transformed into the frequency domain with a 2048 point FFT and ana- lyzed to evaluate the dynamic performance of the A/D ...
Page 19
... CMOS D/A Converter HI20201: 10-Bit, 160MHz, High Speed D/A Converter HI20203: 8-Bit, 160MHz, High Speed D/A Converter HFA1115: 350MHz Programmable Gain Buffer with Output Limiting CMOS Logic Available in HC, HCT, AC, ACT, and FCT. FIGURE 23. 10-BIT COMMUNICATIONS COMPONENTS HI5710A DSP/ P D/A AMP HI1171 HA5020 HI3050 HA2842 HI3338 ...
Page 20
... For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 HI5710A EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ...